2013-2015 Land Cruiser Prado · Service Manual Drivetrain

INSTALLATION

Removal / installation · Vehicles built from Aug 2013


1. INSTALL TRANSMISSION VALVE BODY ASSEMBLY
  1. Install the spring and check ball body.

  1. C157293E02
    Insert the pin of the manual valve into the hole of the manual valve lever.
    Text in Illustration 
    *1
    Pin

  1. C157292E01
    Install the transmission valve body with the 19 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    HINT:
    Each bolt length is indicated below.

    32 mm (1.26 in.) for bolt A
    25 mm (0.984 in.) for bolt B

  1. Install the detent spring and detent spring cover with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


2. CONNECT TRANSMISSION WIRE

  1. C125285E03
    Connect the 7 connectors to the solenoid valves.
    Text in Illustration 
    *1
    Orange
    *2
    Blue

  1. Connect the 2 ATF temperature sensors with the 2 clamps and 2 bolts.

    Torque:
    for bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    12 mm (0.472 in.) for bolt A

    36 mm (1.42 in.) for bolt B


3. INSTALL VALVE BODY OIL STRAINER ASSEMBLY
  1. Coat a new O-ring with ATF and install it to the oil strainer.

  1. Install the oil strainer with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


4. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

NOTICE:
Remove the gasket and be careful not to spill oil on the contacting surfaces of the transmission case and oil pan.

  1. Install a new gasket and the oil pan with the 20 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }


5. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR (for 1KD-FTV)
  1. Install the rear engine mounting insulator to the transmission with the 4 bolts.

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }


6. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY (for 1KD-FTV)
  1. Install the frame crossmember to the engine mounting insulator with the 4 set bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

  1. Connect the ends of the frame crossmember to the vehicle with the 4 bolts and 4 nuts.

    Torque:
    72 N*m{ 734 kgf*cm , 53 ft.*lbf }


7. INSTALL FRONT SUSPENSION MEMBER BRACKET LH AND RH (for 1KD-FTV)
  1. Install the front suspension member bracket LH and front suspension member bracket RH with the 8 bolts.

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }


8. ADD AUTOMATIC TRANSMISSION FLUID
  1. Add automatic transmission fluid (Click here).


9. PERFORM RESET MEMORY
Perform the RESET MEMORY procedures (A/T initialization) (See page 1GR-FE: Click here 1KD-FTV: Click here).
← REASSEMBLY (from Aug 2013)COMPONENTS (from Aug 2013) →