2013-2015 Land Cruiser Prado · Service Manual Drivetrain

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts and No. 1 engine under cover.


3. REMOVE REAR ENGINE UNDER COVER ASSEMBLY
  1. Remove the 4 bolts and rear engine under cover.


4. REMOVE FRONT FENDER APRON SEAL RH
  1. Using a clip remover, remove the 5 clips and front fender apron seal RH.


5. REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL RH
  1. Using a clip remover, remove the 5 clips and front No. 1 fender apron to frame seal RH.


6. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain the ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


7. REMOVE LOWER TRANSFER CASE PROTECTOR
  1. Remove the 4 bolts and lower transfer case protector.


8. REMOVE FRONT EXHAUST PIPE ASSEMBLY
w/ DPF: (Click here)
w/o DPF: (Click here)

9. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
(Click here)

10. REMOVE PROPELLER SHAFT ASSEMBLY
(Click here)

11. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

  1. C214587
    Remove the nut and clip and disconnect the transmission control cable from the transmission.


12. DISCONNECT NO. 1 INLET OIL COOLER TUBE AND NO. 1 OUTLET OIL COOLER TUBE

  1. Remove the 3 bolts and open the 3 oil cooler tube clamps.

    C227715E01

  1. Using a union nut wrench, disconnect the No. 1 inlet oil cooler tube and No. 1 outlet oil cooler tube from each oil cooler tube union.


13. REMOVE STARTER ASSEMBLY
  1. for 2.2 kW Type:
    Remove the starter (Click here).

  1. for 2.7 kW Type:
    Remove the starter (Click here).

  1. for 3.0 kW Type:
    Remove the starter (Click here).


14. REMOVE OIL PAN INSULATOR

C214467
  1. Remove the 2 bolts and oil pan insulator.


15. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

C159641
  1. Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.


16. REMOVE FRONT SUSPENSION MEMBER BRACKET LH AND RH

  1. C214435
    Remove the 8 bolts, front bracket suspension member LH and front bracket suspension member RH.


17. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

  1. C171489
    Remove the 4 bolts of the rear engine mounting insulator.

  1. C214464
    Remove the 4 nuts, 4 bolts and frame crossmember.


18. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

C171491
  1. Remove the 4 bolts and rear engine mounting insulator from the transmission.


19. REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

C218118
  1. Turn the crankshaft to gain access to the 6 bolts and remove each bolt while holding the crankshaft pulley bolt with a wrench.

    HINT:
    If it is difficult to reach the setting bolts with the wrench, raise or lower the transmission jack until there is sufficient space for the wrench.


20. DISCONNECT WIRE HARNESS AND CONNECTOR

  1. C157274
    Tilt the transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.

  1. w/ DPF:

    1. Disconnect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors, differential pressure sensor connector and transfer control side connector.

      C231678

      HINT:
      Detach the claw, press down the lever, and then disconnect the transmission wire connector.

    2. Detach the 10 harness clamps and disconnect the wire harness.

  1. w/o DPF:

    1. Disconnect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors and transfer control side connector.

      C214468E01

      HINT:
      Detach the claw, press down the lever, and then disconnect the transmission wire connector.

    2. Detach the 7 harness clamps and disconnect the wire harness.


21. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

C232274
  1. Remove the 9 bolts and automatic transmission.

    NOTICE:
    Do not use excess force to pry on the transmission assembly.


22. REMOVE NO. 1 SENSOR BRACKET (w/ DPF)

  1. C227716
    Detach the transfer breather hose clamp.

  1. Remove the bolt, nut and No. 1 sensor bracket.


23. REMOVE WIRING HARNESS CLAMP BRACKET (w/ DPF)

  1. C231679
    Remove the bolt and wiring harness clamp bracket.


24. REMOVE TRANSFER ASSEMBLY
(Click here)

25. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

C111232
  1. Remove the 2 bolts and transmission control cable bracket.


26. REMOVE TORQUE CONVERTER ASSEMBLY

27. INSPECT TORQUE CONVERTER ASSEMBLY
(Click here)
← COMPONENTS (from Aug 2013)REMOVAL (from Aug 2014) →