2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P2431 Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Refer to DTC P0412 (Click here).
Refer to DTC P0416 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P2431
P2436
Pressure sensor indicates a value below 45.6 kPa (342 mmHg), or higher than 135 kPa (1013 mmHg) for 5 seconds or more (2 trip detection logic).
  1. Pressure sensor
  2. Open or short in pressure sensor circuit
  3. ECM
P2432
P2437
While the engine is running, voltage output of the pressure sensor is below 0.5 V (1 trip detection logic).
  1. Pressure sensor
  2. Open or short in pressure sensor circuit
  3. ECM
P2433
P2438
While the engine is running, voltage output of the pressure sensor is higher than 4.5 V (1 trip detection logic)
  1. Pressure sensor
  2. Open or short in pressure sensor circuit
  3. ECM

MONITOR DESCRIPTION

A085160E11
The ECM monitors the pressure inside the air passage of the secondary air injection system using the pressure sensor of the air switching valve assembly. If the ECM detects a malfunction in the sensor or sensor circuit, it stores a DTC.

WIRING DIAGRAM

A162276E14

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR - ECM)
  1. Disconnect the pressure sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C44-3 (AIP) - G55-1 (AIP)
    Always
    Below 1 Ω
    C44-2 (VC) - C34-16 (VCV2)
    Always
    Below 1 Ω
    C44-4 (E2) - C35-7 (ETHA)
    Always
    Below 1 Ω
    C45-3 (AIP2) - G55-2 (AIP2)
    Always
    Below 1 Ω
    C45-2 (VC2) - C34-16 (VCV2)
    Always
    Below 1 Ω
    C45-4 (E22) - C35-7 (ETHA)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C44-3 (AIP) or G55-1 (AIP) - Body ground
    Always
    10 kΩ or higher
    C44-2 (VC) or C34-16 (VCV2) - Body ground
    Always
    10 kΩ or higher
    C45-3 (AIP2) or G55-2 (AIP2) - Body ground
    Always
    10 kΩ or higher
    C45-2 (VC2) or C34-16 (VCV2) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the pressure sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT EMISSION CONTROL VALVE SET (PRESSURE SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure (absolute) or Air pump2 pressure (absolute).

  1. Check the pressure displayed on the intelligent tester.

    Standard pressure:
    45 to 135 kPa

    HINT:
    The intelligent tester displays the air pump pressure as an absolute pressure.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Bank 1)
    B
    NG (for Bank 2)
    C



B
REPLACE EMISSION CONTROL VALVE SET (Click here)

C
REPLACE NO. 2 EMISSION CONTROL VALVE SET (Click here)
A

REPLACE ECM (Click here)


← P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (for A/F sensor) (Bank 1 Sensor 1) (+ 9 more codes) (from Aug 2014)P2431 Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1 (+ 5 more codes) (from Aug 2014) →