2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes, clean them with a brush and compressed air.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
(Click here)

3. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.


4. REMOVE FRONT BUMPER LOWER COVER
  1. Remove the clip, 5 bolts and front bumper lower cover.


5. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts and No. 1 engine under cover.


6. REMOVE ENGINE REAR UNDER COVER ASSEMBLY
  1. Remove the 4 bolts and rear engine under cover.


7. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. A218364
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug.

    A245857E01

    Text in Illustration 
    *1
    Radiator Reservoir
    *2
    Vent Plug
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug


8. DISCONNECT HEATER WATER PIPE SUB-ASSEMBLY

  1. A239652
    Detach the water by-pass hose clamp.

  1. Remove the bolt and disconnect the heater water pipe.


9. REMOVE NO. 1 RADIATOR HOSE

A246596

10. REMOVE NO. 3 ENGINE WIRE (for Cold Area Specification Vehicles)

  1. A218418
    Remove the 2 nuts from the battery terminal.

  1. Detach the 3 wire harness clamps.

  1. Remove the No. 3 engine wire from the fan shroud.


11. REMOVE NO. 1 AIR HOSE

  1. A218373
    Loosen the 2 clamps.

  1. Remove the No. 1 air hose from the inlet pipe and intercooler.


12. REMOVE INTERCOOLER AIR HOSE

  1. A224948
    Disconnect the No. 2 vacuum transmitting hose from the intercooler.

  1. A218374
    Loosen the 2 clamps.

  1. Remove the intercooler air hose from the intake pipe and intercooler.


13. REMOVE FAN SHROUD

  1. A218371
    Disconnect the No. 1 water by-pass hose and detach the 2 clamps from the fan shroud.

  1. Disconnect the No. 2 water by-pass hose from the radiator reservoir.

  1. Remove the 3 bolts and radiator reservoir.

  1. for Automatic Transmission:

    1. A218382
      Remove the inlet and outlet oil cooler hoses and detach the clamp from the fan shroud.

    2. Disconnect the 2 oil cooler hoses from the radiator.

  1. A224959
    Loosen the 4 nuts holding the fan with fluid coupling.

  1. Remove the fan and generator V belt (Click here).

  1. A218369
    Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts for the fan with fluid coupling, and then remove the shroud together with the fan with fluid coupling.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Detach the No. 2 water by-pass hose from the hose clamp on the fan shroud.

  1. A224943
    Remove the No. 2 water by-pass hose from the water inlet.

  1. Remove the fan pulley from the water pump.


14. REMOVE NO. 1 AIR CLEANER HOSE

  1. A223211
    Loosen the 2 hose clamps and remove the No. 1 air cleaner hose.


15. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

A246272E02
  1. except Cold Area Specification Vehicles:
    Detach the 2 clamps and disconnect the mass air flow meter connector.

    Text in Illustration 
    *A
    except Cold Area Specification Vehicles
    *B
    for Cold Area Specification Vehicles

  1. for Cold Area Specification Vehicles:
    Detach the 3 clamps and disconnect the mass air flow meter connector.

  1. Detach the 4 clamps and remove the air cleaner cap sub-assembly.


16. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

17. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

  1. A223214
    Remove the 3 bolts and air cleaner case sub-assembly.


18. REMOVE COMPRESSOR OUTLET ELBOW

  1. A223215
    Detach the 3 wire harness clamps.

  1. Remove the bolt and wire harness bracket.

  1. A220719
    Loosen the hose clamp and remove the 2 bolts and compressor outlet elbow.


19. REMOVE VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY (for Cold Area Specification Vehicles)
  1. Disconnect the viscous heater connector.

  1. A223522
    Disconnect the water by-pass hose and water hose.

  1. A223524
    Remove the 2 bolts and viscous heater with magnet clutch.


20. REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (for Cold Area Specification Vehicles)

  1. A223525
    Remove the 4 bolts and No. 1 viscous heater bracket.


21. DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

  1. A223526
    Disconnect the compressor connector.

  1. Remove the 4 bolts and disconnect the cooler compressor.


22. REMOVE GENERATOR BRACKET

  1. A239369
    Remove the bolt and generator bracket.


23. REMOVE GENERATOR ASSEMBLY

  1. A222880
    Disconnect the generator connector.

  1. Remove the terminal cap.

  1. Remove the nut and disconnect the generator wire.

  1. Remove the 2 bolts and generator.


24. REMOVE NO. 2 IDLER PULLEY ASSEMBLY

  1. A239370
    Remove the bolt, pulley plate, No. 2 idle pulley and spacer.


25. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

  1. A244867
    Remove the 5 bolts and No. 1 compressor mounting bracket.


26. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY
(Click here)

27. DISCONNECT WIRE HARNESS

  1. A245686
    Remove the bolt and disconnect the wire harness.

  1. A246260
    for LHD:
    Remove the bolt and disconnect the wire harness.

  1. Detach the 5 clamps and disconnect the wire harness from the cowl top panel.


28. REMOVE MANIFOLD ABSOLUTE PRESSURE SENSOR

  1. A239598
    Disconnect the manifold absolute pressure sensor connector and vacuum hose.

  1. Remove the bolt and manifold absolute pressure sensor.


29. REMOVE EMISSION CONTROL VALVE BRACKET

  1. A239639
    Remove the bolt and emission control valve bracket.


30. REMOVE THROTTLE BODY BRACKET

  1. A244614
    Remove the 3 bolts and throttle body bracket.


31. REMOVE NO. 1 GAS FILTER

  1. A244608
    Disconnect the vacuum hose and remove the No. 1 gas filter from the gas filter bracket.


32. REMOVE GAS FILTER BRACKET

  1. A246247
    Detach the clamp and disconnect the wire harness.

  1. A244609
    Remove the bolt and gas filter bracket.


33. REMOVE INTAKE AIR CONNECTOR

  1. A245684
    Remove the 3 bolts, intake air connector and gasket.


34. REMOVE NO. 1 FUEL PIPE
  1. Disconnect the No. 2 fuel pipe (Click here).

  1. Remove the 4 bolts, union bolt, gasket and No. 1 fuel pipe.

    A239663E01

    Text in Illustration 
    *1
    No. 2 Fuel Pipe
    -
    -
    V100136
    Union Bolt
    -
    -


35. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

  1. A239621
    Remove the bolt, nut and 2 No. 2 injection pipe clamps.

  1. A239619E01
    Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
    Text in Illustration 
    *a
    Common Rail Side
    *b
    Injector Side


36. REMOVE NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A244984
    Remove the 4 bolts and No. 2 cylinder head cover.


37. REMOVE VENTILATION PIPE

  1. A308001
    Type A
    Slide the 2 clamps and disconnect the No. 3 turbo water hose and No. 4 turbo water hose from the ventilation pipe.

  1. A308002E01
    Remove the bolt and disconnect the 2 ventilation hoses and ventilation pipe from the cylinder head sub-assembly.
    Text in Illustration 
    *A
    Type A
    *B
    Type B


38. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

NOTICE:
If the cylinder head cover is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.

  1. A060180E01
    Using a small screwdriver, remove the nozzle holder seal by prying the portion between the nozzle holder seal and the cutout part of the cylinder head cover.

  1. A223193
    Remove the 10 bolts, 2 nuts, cylinder head cover and cylinder head cover gasket.

  1. A289511
    Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.


39. REMOVE NO. 1 TIMING BELT COVER

  1. A015094E01
    Remove the 6 bolts, 6 washers and timing belt cover.


40. REMOVE TIMING BELT

  1. A070549E05
    Turn the crankshaft clockwise and align the timing marks as shown in the illustration.
    Text in Illustration 
    *1
    Timing Mark

    HINT:
    If reusing the timing belt, place matchmarks on the timing belt so that it can be installed exactly as before.

  1. A070550E01
    Uniformly loosen and remove the 2 bolts and No. 1 timing belt tensioner.

  1. Remove the timing belt.

    HINT:
    A070551E02
    1. If turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise as shown in the illustration.
    2. When installing the timing belt, turn the camshaft to align the timing marks and then turn the crankshaft clockwise to align the timing marks.


41. REMOVE CAMSHAFT TIMING PULLEY

  1. A060182E01
    Remove the bolt of the camshaft timing pulley while holding the camshaft with a wrench.

    NOTICE:
    Make sure the timing belt is not installed when removing the bolt of camshaft timing pulley.

  1. Remove the camshaft timing pulley.


42. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

NOTICE:
When inspecting the No. 1 timing belt idler, do not remove it unless absolutely necessary.

  1. Using a 10 mm hexagon wrench, remove the bolt, No. 1 timing belt idler and washer.


43. REMOVE NO. 2 TIMING BELT COVER

  1. A225464
    Remove the 4 bolts, nut and No. 2 timing belt cover.


44. REMOVE CYLINDER BLOCK INSULATOR

  1. A149941
    Remove the cylinder block insulator from the cylinder head.


45. REMOVE ENGINE WATER PUMP ASSEMBLY

  1. A299976
    Remove the 2 nuts, 5 bolts, engine water pump assembly and the gasket from the cylinder block sub-assembly.

  1. A224975
    Remove the bolt, water pump assembly without cover and the gasket from the water pump cover.


46. REPLACE STUD BOLT

HINT:
Perform this procedure only when replacement of the stud bolts is necessary.

  1. A267255
    Remove the 4 stud bolts from the water pump assembly without cover.

  1. Install the 4 stud bolts to the water pump assembly without cover.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }


47. REPLACE WATER PUMP SET RING PIN

HINT:
Perform this procedure only when replacement of the water pump set ring pin is necessary.

  1. A267256
    Remove the water pump set ring pin from the water pump cover.

  1. Using a plastic-faced hammer, tap in the water pump set ring pin to the water pump cover.

← ON-VEHICLE INSPECTION (from Aug 2013)REMOVAL (from Aug 2014) →