1.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
2.
REMOVE UPPER RADIATOR SUPPORT SEAL
Remove the 13 clips and upper radiator support seal.
3.
REMOVE FRONT BUMPER LOWER COVER
Remove the clip, 5 bolts and front bumper lower cover.
4.
REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
Remove the 4 bolts and No. 1 engine under cover.
5.
REMOVE ENGINE REAR UNDER COVER ASSEMBLY
Remove the 4 bolts and rear engine under cover.
6.
DRAIN ENGINE COOLANT
CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
Loosen the radiator drain cock plug.
HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.
Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.
Loosen the cylinder block drain cock plug.
Text in Illustration
*1
Radiator Reservoir
*2
Vent Plug
*3
Radiator Drain Cock Plug
*4
Cylinder Block Drain Cock Plug
7.
REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System)
Remove the electric EGR control valve assembly (Click here).
8.
DISCONNECT INLET HEATER WATER HOSE (w/o EGR System)
Remove the bolt and disconnect the inlet heater water hose.
Remove the 4 bolts and No. 1 viscous heater bracket.
32.
DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
Disconnect the compressor connector.
Remove the 4 bolts and disconnect the cooler compressor.
33.
REMOVE GENERATOR BRACKET
Remove the bolt and generator bracket.
34.
REMOVE GENERATOR ASSEMBLY
Disconnect the generator connector.
Remove the terminal cap.
Remove the nut and disconnect the generator wire.
Remove the 2 bolts and generator.
35.
REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
Remove the 5 bolts and No. 1 compressor mounting bracket.
36.
REMOVE VENTILATION PIPE
Type A Slide the 2 clamps and disconnect the No. 3 turbo water hose and No. 4 turbo water hose from the ventilation pipe.
Remove the bolt and disconnect the 2 ventilation hoses and ventilation pipe from the cylinder head sub-assembly.
Text in Illustration
*A
Type A
*B
Type B
37.
REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
NOTICE:
If the cylinder head cover is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.
Using a small screwdriver, remove the nozzle holder seal by prying the portion between the nozzle holder seal and the cutout part of the cylinder head cover.
Remove the 10 bolts, 2 nuts, cylinder head cover and cylinder head cover gasket.
Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.
38.
REMOVE NO. 1 TIMING BELT COVER
Remove the 6 bolts, 6 washers and timing belt cover.
39.
REMOVE TIMING BELT
Turn the crankshaft clockwise and align the timing marks as shown in the illustration.
Text in Illustration
*1
Timing Mark
HINT:
If reusing the timing belt, place matchmarks on the timing belt so that it can be installed exactly as before.
Uniformly loosen and remove the 2 bolts and No. 1 timing belt tensioner.
Remove the timing belt.
HINT:
If turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise as shown in the illustration.
When installing the timing belt, turn the camshaft to align the timing marks and then turn the crankshaft clockwise to align the timing marks.
40.
REMOVE CAMSHAFT TIMING PULLEY
Remove the bolt of the camshaft timing pulley while holding the camshaft with a wrench.
NOTICE:
Make sure the timing belt is not installed when removing the bolt of camshaft timing pulley.
Remove the camshaft timing pulley.
41.
REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY
NOTICE:
When inspecting the No. 1 timing belt idler, do not remove it unless absolutely necessary.
Using a 10 mm hexagon wrench, remove the bolt, No. 1 timing belt idler and washer.
42.
REMOVE NO. 2 TIMING BELT COVER
Remove the 4 bolts, nuts and No. 2 timing belt cover.
43.
REMOVE CYLINDER BLOCK INSULATOR
Remove the cylinder block insulator from the cylinder head.
44.
REMOVE ENGINE WATER PUMP ASSEMBLY
Remove the 2 nuts, 5 bolts, engine water pump assembly and the gasket from the cylinder block sub-assembly.
Remove the bolt, water pump assembly without cover and the gasket from the water pump cover.
45.
REPLACE STUD BOLT
HINT:
Perform this procedure only when replacement of the stud bolts is necessary.
Remove the 4 stud bolts from the water pump assembly without cover.
Install the 4 stud bolts to the water pump assembly without cover.
Torque:
7.8 N*m{
80 kgf*cm
, 69 in.*lbf
}
46.
REPLACE WATER PUMP SET RING PIN
HINT:
Perform this procedure only when replacement of the water pump set ring pin is necessary.
Remove the water pump set ring pin from the water pump cover.
Using a plastic-faced hammer, tap in the water pump set ring pin to the water pump cover.