2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

INSPECTION

Inspection · Vehicles built from Aug 2013


INSPECT STARTER ASSEMBLY

CAUTION:
As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may became hot and cause injury.

NOTICE:
The following tests must each be performed within 3 to 5 seconds to prevent the coil from burning out.

  1. Mount the starter in a vise between aluminum plates.

  1. Perform a pull-in test.

    1. Remove the nut, and then disconnect the lead wire from terminal C.

    2. A222272E01
      Connect the battery to the magnet starter switch as shown in the illustration. Check that the clutch pinion gear extends.
      Text in Illustration 
      *1
      Terminal C
      *2
      Terminal 50
      If the clutch pinion gear does not move, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.

  1. Perform a holding test.

    1. A222273E01
      Disconnect the negative (-) terminal lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the pinion gear remains extended.
      Text in Illustration 
      *1
      Terminal C
      If the clutch pinion gear returns inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.

  1. Inspect the clutch pinion gear return.

    1. A222274
      Disconnect the negative (-) terminal lead from the starter body. Check that the clutch pinion gear returns inward.
      If the clutch pinion gear does not return inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.

  1. Perform an operation test without load.

    1. Connect the field coil lead wire to terminal C.

      Torque:
      5.9 N*m{ 60 kgf*cm , 52 in.*lbf }

    2. A222275E01
      Connect the battery and an ammeter to the starter as shown in the illustration.
      Text in Illustration 
      *1
      Terminal 30
      *2
      Terminal 50

    3. Check that the starter rotates smoothly and steadily while the pinion gear is extended. Then measure the current.

      Specified current:
      120 A or less at 11.5 V

      If the result is not as specified, inspect the starter assembly.

      HINT:
      Inspect the starter brush holder assembly, starter yoke assembly and starter armature assembly. If there is a malfunction, replace the part and perform this test again.


INSPECT MAGNET STARTER SWITCH ASSEMBLY

  1. Inspect the pull-in coil.

    1. A074034E02
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal C - Terminal 50
      Always
      Below 1 Ω

      Text in Illustration 
      *1
      Terminal C
      *2
      Terminal 50
      If the result is not as specified, replace the magnet starter switch assembly.

  1. Inspect the holding coil.

    1. A074035E02
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Switch body - Terminal 50
      Always
      Below 2 Ω

      Text in Illustration 
      *1
      Switch Body
      *2
      Terminal 50
      If the result is not as specified, replace the magnet starter switch assembly.


INSPECT BRUSH

  1. B000900E02
    Using a vernier caliper, measure the brush length.
    Text in Illustration 
    *1
    Length
    *a
    Brush Holder Side
    *b
    Starter Yoke Side

    Standard brush length:
    16.5 mm (0.650 in.)

    Minimum brush length:
    9.0 mm (0.354 in.)

    1. If the length is less than the minimum, replace the brush holder and starter yoke assembly.


INSPECT STARTER BRUSH HOLDER ASSEMBLY

  1. P021088E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Positive (+) brush holder - Negative (-) brush holder
    Always
    10 kΩ or higher

    1. If the result is not as specified, replace the starter brush holder assembly.

  1. Check the brush spring load.

    1. ST00019E11
      Take a pull scale reading immediately after the brush spring separates from the brush.

      Standard spring load:
      27 to 32 N (2.7 to 3.3 kgf, 6.0 to 7.3 lbf)

      Minimum spring load:
      18 N (2 kgf, 4.0 lbf)

      Text in Illustration 
      *1
      Brush Spring
      *2
      Brush
      If the spring load is less than the minimum, replace the brush holder assembly.


INSPECT STARTER YOKE ASSEMBLY

  1. Inspect for an open circuit.

    1. A222269
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Lead wire - Brush
      Always
      Below 1 Ω

      If the result is not as specified, replace the starter yoke assembly.

  1. Inspect for a short circuit.

    1. A222270
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Starter yoke body - Brush
      Always
      10 kΩ or higher

      If the result is not as specified, replace the starter yoke assembly.


INSPECT STARTER ARMATURE ASSEMBLY
  1. Check the commutator for dirt and/or burns on the surface.
    If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe. Replace the armature if necessary.

  1. Inspect the commutator for an open circuit.

    1. ST01098E02
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Segment
      Always
      Below 1 Ω

      Text in Illustration 
      *1
      Segment
      If the result is not as specified, replace the starter armature assembly.

  1. Inspect the commutator for a short circuit.

    1. ST01099E02
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Coil core
      Always
      10 kΩ or higher

      Text in Illustration 
      *1
      Segment
      *2
      Coil Core
      If the result is not as specified, replace the starter armature assembly.

  1. Inspect the commutator circle runout.

    1. S004640E01
      Place the armature on V-blocks.

    2. Using a dial indicator, measure the circle runout.

      Maximum circle runout:
      0.05 mm (0.00197 in.)

      If the runout is more than the maximum, correct it with sandpaper (No. 400) or replace the starter armature assembly.

  1. ST01100E01
    Using a vernier caliper, measure the commutator diameter.

    Standard diameter:
    35.0 mm (1.38 in.)

    Minimum diameter:
    34.0 mm (1.34 in.)

    If the diameter is less than the minimum, replace the starter armature assembly.

  1. ST00040E01
    Measure the undercut depth of the commutator.

    Standard depth:
    0.7 mm (0.0276 in.)

    Minimum depth:
    0.2 mm (0.00787 in.)

    If the undercut depth is less than the minimum, correct it with a hacksaw blade.

  1. Inspect the bearings.

    1. Check that the bearing rotates smoothly.
      If the result is not as specified, replace the starter armature assembly.


INSPECT STARTER CLUTCH SUB-ASSEMBLY

  1. A223418
    Rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.
    Text in Illustration 
    V100135
    Free
    V100136
    Lock
    If the result is not as specified, replace the starter clutch sub-assembly.

  1. Turn the pinion gear by hand while applying inward force and check the movement of the bearing.
    If resistance is felt or the bearing sticks, replace the starter clutch sub-assembly.

← DISASSEMBLY (from Aug 2013)REASSEMBLY (from Aug 2013) →