2013-2015 Land Cruiser Prado · Service Manual Drivetrain

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013


1. FIX REAR DIFFERENTIAL CARRIER ASSEMBLY IN PLACE

C217291
  1. Fix the rear differential carrier assembly to the overhaul attachment.


2. INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR

F001237E19
  1. Using a dial indicator, measure the runout of the companion flange vertically and laterally.

    Distance from center to runout measurement point:
    30 mm (1.18 in.)

    Maximum Runout:
    Item
    Specified Condition
    Vertical runout
    0.10 mm (0.00394 in.)
    Lateral runout
    0.10 mm (0.00394 in.)

    Text in Illustration 
    *a
    Vertical Runout
    *b
    Lateral Runout
    If the runout is more than the maximum, replace the companion flange.


3. INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

C217282
  1. Using a dial indicator, check the runout of the ring gear.

    Maximum runout:
    0.07 mm (0.00276 in.)

    If the runout is more than the maximum, replace the ring gear with a new one.


4. INSPECT DIFFERENTIAL RING GEAR BACKLASH

C217283
  1. Using a dial indicator, check the backlash of the ring gear.

    Standard backlash:
    0.10 to 0.20 mm (0.00394 to 0.00787 in.)

    If the backlash is not within the specification, adjust the side bearing preload or performs repairs as necessary.


5. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

C003092
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Standard preload (at starting):
    0.88 to 1.98 N*m (9.0 to 20.2 kgf*cm, 7.8 to 17.5 in.*lbf)

    If necessary, disassemble and inspect the differential assembly.


6. INSPECT TOTAL PRELOAD

C003092
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

  1. Using a torque wrench, measure the total preload.

    Standard Total Preload (at starting):
    Drive pinion preload plus 0.20 to 0.40 N*m (2.0 to 4.1 kgf*cm, 1.8 to 3.5 in.*lbf)

    If necessary, disassemble and inspect the differential.


7. REMOVE DIFFERENTIAL LOCK SHIFT ACTUATOR

G020268
  1. Remove the 4 bolts and actuator from the differential carrier.

  1. Remove the O-ring.


8. REMOVE DIFFERENTIAL LOCK INDICATOR SWITCH

G020269
  1. Remove the indicator switch and gasket.


9. REMOVE REAR DIFFERENTIAL LOCK SHIFT FORK SHAFT

G020270
  1. Using a 6 mm hexagon wrench, remove the 2 screw plugs.

  1. Remove the spring seat, spring and ball.

  1. G020271
    Using a 5 mm pin punch and hammer, remove the slotted pin.

  1. G020272
    Remove the 2 bolts from the shaft retainer.

  1. Using a plastic-faced hammer, remove the shaft retainer.

  1. Remove the shift fork shaft.

  1. Remove the rear differential lock sleeve.


10. REMOVE REAR DRIVE PINION NUT

F044346E02
  1. Using SST and a hammer, loosen the staked part of the nut.

    SST
    09930-00010  

    NOTICE:
    1. Be sure to use SST with the tapered surface facing the shaft.
    2. Do not grind the tip of SST with a grinder, etc.
    3. Completely loosen the staked part of the nut when removing.
    4. Do not damage the threads of the drive pinion.

  1. SA02349E06
    Use SST to hold the drive pinion companion flange.
    SST
    09330-00021  

  1. Using a 30 mm socket wrench, remove the rear drive pinion nut.


11. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR

F052175E02
  1. Using SST, remove the drive pinion companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Apply grease to the threads and tip of SST center bolt before use.


12. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

SA02348E03
  1. Using SST, remove the oil seal from the differential carrier.

    SST
    09308-10010  


13. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

NOTICE:
Apply grease to the threads and tip of SST center bolt before use.


14. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING (INNER)

Z000641E04
  1. Using SST, remove the drive pinion tapered roller bearing from the drive pinion.

    SST
    09556-22010  

    NOTICE:
    Apply grease to the threads and tip of SST center bolt before use.


15. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING (OUTER)

16. REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

C217052
  1. Remove the 2 bolts and 2 rear differential bearing adjusting nut locks.


17. REMOVE DIFFERENTIAL CASE ASSEMBLY

C217292E01
  1. Place matchmarks on the bearing cap and differential carrier.

    Text in Illustration 
    *a
    Matchmark

  1. Remove the 4 bolts and 2 differential bearing caps.

  1. Remove the 2 adjusting nuts.

  1. C217285
    Remove the rear differential case sub-assembly and 2 case bearings from the differential carrier.

    HINT:
    Tag the 2 case bearing outer races so that they can be reinstalled in the correct locations.


18. REMOVE DIFFERENTIAL DRIVE PINION

C030540
  1. Remove the differential drive pinion and bearing spacer from the differential carrier.


19. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING (INNER)

R010668E02
  1. Using SST and a press, remove the drive pinion tapered roller bearing from the drive pinion.

    SST
    09950-00020  

    HINT:
    If either the drive pinion or ring gear is damaged, replace them as a set.

    NOTICE:
    Do not drop the drive pinion.


20. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING (OUTER)

C091047
  1. Using a brass bar and hammer, remove the rear tapered roller bearing from the carrier.

    HINT:
    If the bearing is damaged during the removal, replace it.


21. REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER

22. REMOVE DIFFERENTIAL RING GEAR

C216547E02
  1. Place matchmarks on the ring gear and differential case.

    Text in Illustration 
    *a
    Matchmark

  1. Using a screwdriver and hammer, unstake the lock plates.

  1. Remove the 12 ring gear set bolts.

  1. C014054
    Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


23. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

F044358E02
  1. Using SST, remove the front tapered roller bearing from the carrier.

    SST
    09308-00010  

  1. Using a brass bar and hammer, remove the oil storage ring from the carrier.

    HINT:
    If the bearing is damaged during the removal, replace it.


24. INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT

G020277
  1. Install the rear differential case bearing to the differential case.

  1. Install the differential case to the differential carrier.

  1. Install the 2 bearing caps to the differential carrier with the 4 bolts.

    Torque:
    103 N*m{ 1049 kgf*cm , 76 ft.*lbf }

  1. Inspect the differential case runout.

    Maximum runout:
    0.07 mm (0.00276 in.)

  1. Remove the differential case.

  1. Remove the rear differential case bearing.


25. REMOVE REAR DIFFERENTIAL CASE BEARING

F040345E03
  1. Using SST, remove the 2 rear differential case bearings from the differential case.

    SST
    09950-40011   (09953-04020, 09951-04010, 09952-04010, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00500, 09951-00650, 09952-06010)


26. DISASSEMBLE DIFFERENTIAL CASE

F052178E03
  1. Place matchmarks on the LH and RH cases.

    Text in Illustration 
    *a
    Matchmark

  1. Remove the 8 bolts.

  1. ZK09094
    Using a plastic-faced hammer, separate the LH and RH cases.

  1. C090324E05
    Remove the parts shown in the illustration from the differential case.
    Text in Illustration 
    *1
    Side Gear
    *2
    Side Gear Thrust Washer
    *3
    Spider
    *4
    Pinion Gear
    *5
    Pinion Gear Thrust Washer

← REMOVAL (from Aug 2013)INSPECTION (from Aug 2013) →