2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

INSPECTION

Inspection · Vehicles built from Aug 2013


INSPECT GENERATOR WITH CLUTCH PULLEY

  1. A222452
    Hold the center of the generator with clutch pulley and confirm that the outer ring turns counterclockwise and does not turn clockwise.
    Text in Illustration 
    V100135
    Free
    V100136
    Lock
    If the result is not as specified, replace the generator with clutch pulley.


INSPECT GENERATOR BRUSH HOLDER ASSEMBLY

  1. A220296E01
    Using a vernier caliper, measure the brush length.

    Standard exposed length:
    9.5 to 11.5 mm (0.374 to 0.453 in.)

    Minimum exposed length:
    4.5 mm (0.177 in.)

    Text in Illustration 
    *1
    Length
    If the brush length is less than the minimum, replace the generator brush holder assembly.


INSPECT GENERATOR REGULATOR ASSEMBLY

  1. A220297E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Terminal F - Terminal B
    Always
    Below 1 Ω or higher than 10 kΩ

    Text in Illustration 
    *1
    Terminal F
    *2
    Terminal B
    If the result is not as specified, replace the generator regulator assembly.

    HINT:
    When the ohmmeter leads are initially touched to the regulator, one of the above values is output.
    When the leads are reversed, the reading changes to the other value.

  1. A220298E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Terminal F - Terminal E
    Always
    Below 1 Ω or higher than 10 kΩ

    Text in Illustration 
    *1
    Terminal F
    *2
    Terminal E
    If the result is not as specified, replace the generator regulator assembly.

    HINT:
    When the ohmmeter leads are initially touched to the regulator, one of the above values is output.
    When the leads are reversed, the reading changes to the other value.


INSPECT GENERATOR HOLDER WITH RECTIFIER

  1. Inspect the positive (+) rectifier.

    1. A220299E01
      Using an ohmmeter, connect one tester probe to the positive (+) terminal and the other to each rectifier terminal.
      Text in Illustration 
      *1
      Positive (+) Terminal
      *2
      Rectifier Terminal

    2. Reverse the polarity of the tester probes and repeat the step above.

    3. Check that one polarity shows a resistance of below 1 Ω and the other shows a resistance of 10 kΩ or higher.
      If the result is not as specified, replace the generator holder with rectifier.

  1. Inspect the negative (-) rectifier.

    1. A220300E01
      Using an ohmmeter, connect one tester probe to the negative (-) terminal and the other to each rectifier terminal.
      Text in Illustration 
      *1
      Negative (-) Terminal
      *2
      Rectifier Terminal

    2. Reverse the polarity of the tester probes and repeat the step above.

    3. Check that one polarity shows a resistance of below 1 Ω and the other shows a resistance of 10 kΩ or higher.
      If the result is not as specified, replace the generator holder with rectifier.


INSPECT GENERATOR ROTOR ASSEMBLY

  1. Check the generator rotor for an open circuit.

    1. A220301E01
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Slip ring - Slip ring
      20°C (68°F)
      1.7 to 2.1 Ω

      Text in Illustration 
      *1
      Slip Ring
      If the result is not as specified, replace the generator rotor assembly.

  1. Check if the generator rotor is grounded.

    1. A220302E01
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Slip ring - Rotor core
      Always
      10 kΩ or higher

      Text in Illustration 
      *1
      Slip Ring
      *2
      Coil Core
      If the result is not as specified, replace the generator rotor assembly.

  1. Inspect the slip rings.

    1. Check that the slip rings are not rough or scored.
      If the slip lings are rough or scored, replace the generator rotor assembly.

    2. A220303E01
      Using a vernier caliper, measure the slip ring diameter.

      Standard diameter:
      14.2 to 14.4 mm (0.559 to 0.567 in.)

      Minimum diameter:
      14.0 mm (0.551 in.)

      Text in Illustration 
      *1
      Diameter
      If the diameter is less than the minimum, replace the generator rotor assembly.

← DISASSEMBLY (from Aug 2013)REASSEMBLY (Aug 2013 – Jul 2014) →