2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

REASSEMBLY

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Install the generator rotor to the generator drive end frame.

    NOTICE:
    Do not drop the generator rotor assembly.

  1. Install the washer to the generator rotor.

  1. A220304E01
    Using a 17 mm socket wrench and press, slowly press on the rectifier end frame.
    Text in Illustration 
    *1
    17 mm Socket Wrench

  1. Install the 4 nuts.

    Torque:
    4.5 N*m{ 46 kgf*cm , 40 in.*lbf }

  1. Install the 3 terminal insulators to the rectifier end frame.


2. INSTALL GENERATOR HOLDER WITH RECTIFIER
  1. Install the generator holder with rectifier with the 3 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 17 in.*lbf }


3. INSTALL GENERATOR REGULATOR ASSEMBLY
  1. Install the generator regulator with the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 17 in.*lbf }


4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY
  1. Install the plate seal.

  1. Install the generator brush holder with the 3 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 17 in.*lbf }

  1. Install the brush cover to the generator brush holder.

  1. Install the terminal insulator with the nut.

    Torque:
    4.1 N*m{ 42 kgf*cm , 36 in.*lbf }

  1. Install the generator rear end cover with the 2 nuts.

    Torque:
    4.4 N*m{ 45 kgf*cm , 39 in.*lbf }

  1. Install the rectifier plate with the nut and screw.

    Torque:
    for nut:
    4.4 N*m{ 45 kgf*cm , 39 in.*lbf }
    for screw:
    3.9 N*m{ 39 kgf*cm , 34 in.*lbf }


5. INSTALL GENERATOR WITH CLUTCH PULLEY
  1. Temporarily install the generator with clutch pulley to the generator rotor shaft by hand.

  1. Mount the generator in a vise between aluminum plates.

  1. A219545E01
    Install SST (A) and SST (B) to the generator with clutch pulley as shown in the illustration.
    SST
    09820-63021  
    Text in Illustration 
    *1
    Rotor Shaft

    NOTICE:
    Securely attach SST to the generator with clutch pulley and generator rotor shaft.

  1. A219547E02
    Using a wrench to hold SST (A), turn SST (B) clockwise to tighten the generator with clutch pulley.

    Torque:
    without SST:
    111 N*m{ 1127 kgf*cm , 81 ft.*lbf }
    with SST:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }

    Text in Illustration 
    *1
    Fulcrum Length
    *a
    Hold
    V100135
    Turn

    HINT:
    1. Use a torque wrench with a fulcrum length of 400 mm (15.7 in.). When using a torque wrench with a fulcrum length that is not 400 mm (15.7 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and the wrench are connected in a straight line.

    HINT:
    Be careful as the generator with clutch pulley or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.

  1. Remove SST from the generator.

  1. Check that the generator with clutch pulley rotates smoothly.


6. INSTALL GENERATOR PULLEY CAP
  1. Install a new generator pulley cap to the generator with clutch pulley.

← INSPECTION (from Aug 2013)REASSEMBLY (from Aug 2014) →