Rear Fog Light Circuit
Circuit diagnosis · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The main body ECU receives headlight dimmer switch information signals and illuminates the rear fog lights.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR FOG LIGHT RELAY) |
 |
Using the intelligent tester, perform the Active Test (Click here).
Main Body
Tester Display
|
Test Part
|
Control Range
|
Diagnostic Note
|
Rear Fog Light Relay
|
Rear fog light relay
|
ON/OFF
|
The headlight dimmer switch is in the tail position.
|
- OK:
- Rear fog light relay operates (rear fog lights come on).
|
NG |
 |
|
|
|
| OK |
|
 |
|
| PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
|
|
| 2. INSPECT REAR FOG LIGHT RELAY (FOG RR) |
 |
- Remove the rear fog light relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
3 - 5
|
Battery voltage not applied between terminals 1 and 2
|
10 kΩ or higher
|
Battery voltage applied between terminals 1 and 2
|
Below 1 Ω
|
|
NG |
 |
|
| REPLACE REAR FOG LIGHT RELAY |
|
|
| OK |
|
 |
|
| 3. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY [FOG RR] - BATTERY) |
 |
- Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
Rear fog light relay terminal 5 - Body ground
|
Always
|
11 to 14 V
|
Rear fog light relay terminal 2 - Body ground
|
Headlight dimmer switch off
|
Below 1 V
|
Headlight dimmer switch tail
|
11 to 14 V
|
Text in Illustration
*a
|
Front view of wire harness connector (to Rear Fog Light Relay)
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 4. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY [FOG RR] - MAIN BODY ECU) |
 |
Remove the main body ECU (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
Rear fog light relay terminal 1 - A-27 (RFGO)
|
Always
|
Below 1 Ω
|
A-27 (RFGO) - Body ground
|
Always
|
10 kΩ or higher
|
|
NG |
 |
|
|
|
| OK |
|
 |
|
| REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
|
|
| 5. INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY |
 |
- Remove the driver side junction block assembly (Click here).
Remove the main body ECU from the driver side junction block assembly (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
2F-19 - A-27
|
Always
|
Below 1 Ω
|
|
NG |
 |
|
| REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY (Click here)
|
|
|
| OK |
|
 |
|
| REPAIR OR REPLACE HARNESS AND CONNECTOR |
|