2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

Rear Fog Light Circuit

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The main body ECU receives headlight dimmer switch information signals and illuminates the rear fog lights.

WIRING DIAGRAM

E200982E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR FOG LIGHT RELAY)
  1. Using the intelligent tester, perform the Active Test (Click here).

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Rear Fog Light Relay
    Rear fog light relay
    ON/OFF
    The headlight dimmer switch is in the tail position.

    OK:
    Rear fog light relay operates (rear fog lights come on).



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT REAR FOG LIGHT RELAY (FOG RR)

  1. E183428E02
    Remove the rear fog light relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied between terminals 1 and 2
    10 kΩ or higher
    Battery voltage applied between terminals 1 and 2
    Below 1 Ω



NG
REPLACE REAR FOG LIGHT RELAY
OK


3. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY [FOG RR] - BATTERY)

  1. E200983E01
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Rear fog light relay terminal 5 - Body ground
    Always
    11 to 14 V
    Rear fog light relay terminal 2 - Body ground
    Headlight dimmer switch off
    Below 1 V
    Headlight dimmer switch tail
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Fog Light Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY [FOG RR] - MAIN BODY ECU)
  1. Remove the main body ECU (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Rear fog light relay terminal 1 - A-27 (RFGO)
    Always
    Below 1 Ω
    A-27 (RFGO) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 5
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

5. INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

  1. E283382E04
    Remove the driver side junction block assembly (Click here).

  1. Remove the main body ECU from the driver side junction block assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2F-19 - A-27
    Always
    Below 1 Ω



NG
REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR


← Front Fog Light Circuit (from Aug 2014)Rear Fog Light Circuit (from Aug 2014) →