2013-2015 Land Cruiser Prado · Service Manual Brake

TC and CG Terminal Circuit

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

WIRING DIAGRAM

C200425E15

HINT:
When each warning light continues blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.


INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform calibration (Click here).


1. INSPECT DLC3
  1. Turn the ignition switch to ON.

  1. C146309E17
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G48-13 (TC) - G48-4 (CG)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 4
OK


2. CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (for LHD: Click here, for RHD: Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


3. CHECK DTC (CAN COMMUNICATION SYSTEM)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Check for DTCs (for LHD: Click here, for RHD: Click here).

    Result 
    Result
    Proceed to
    CAN system DTC is not output
    A
    CAN system DTC is output (for LHD)
    B
    CAN system DTC is output (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


4. CHECK HARNESS AND CONNECTOR (ECM - DLC3)
  1. Turn the ignition switch off.

  1. for 1GR-FE:Disconnect the G56 ECM connector.for 1KD-FTV:Disconnect the G58 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE 
    Tester Connection
    Condition
    Specified Condition
    G56-28 (TC) - G48-13 (TC)
    Always
    Below 1 Ω
    for 1KD-FTV 
    Tester Connection
    Condition
    Specified Condition
    G58-23 (TC) - G48-13 (TC)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G48-4 (CG) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK ECM (DLC3 INPUT)
  1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

  1. C146309E17
    Check that the MIL is blinking.
    Result 
    Result
    Proceed to
    MIL is blinking
    A
    MIL is not blinking
    B
    Text in Illustration 
    *a
    Front view of DLC3

HINT:
Refer to the ECM installation procedures:
for 1GR-FE (Click here)
for 1KD-FTV (Click here)



B
REPAIR OR REPLACE WIRE HARNESS OR ECM
A


7. CHECK DTC (CAN COMMUNICATION SYSTEM)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Check for DTCs (for LHD: Click here, for RHD: Click here).

    Result 
    Result
    Proceed to
    CAN system DTC is not output (for LHD)
    A
    CAN system DTC is not output (for RHD)
    B
    CAN system DTC is output (for LHD)
    C
    CAN system DTC is output (for RHD)
    D



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

D
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)


← TC and CG Terminal Circuit (Aug 2013 – Jul 2014)TS and CG Terminal Circuit (from Aug 2013) →