INSPECTION
Inspection · Vehicles built from Aug 2013
| INSPECT DIFFERENTIAL LOCK SYSTEM |
![]() ![]() |
Inspect the indicator light.
Check that the indicator light lights up approximately 1 second after the ignition switch is turned to ON.
Inspect the differential lock operation.
Jack up the vehicle and start the engine.
Set the transfer to L4 or L4L.
When the differential lock control switch is set to the ON position, check that the indicator light turns on. Differential lock is applied to the rear wheels at this time.
- HINT:
- If the gears of the differential lock system are not engaged, the indicator light continues blinking, so rotate the tires to engage the gears.
When the differential lock control switch is in the OFF position, check that the indicator light goes off. The rear differential lock is released at this time.
Stop the engine and lower the vehicle.
| INSPECT FOUR WHEEL DRIVE CONTROL ECU (POWER SUPPLY) |
![]() ![]() |
Check the harness and connector (ECU - battery and body ground).
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G54-3 (IG) - Body ground
Ignition switch ON
11 to 14 V
If the result is not as specified, inspect the harness and connector or 4WD fuse. If the harness is malfunctioning, repair or replace the harness and connector or 4WD fuse. If the harness and connector are normal, replace the four wheel drive control ECU (Click here).Text in Illustration *a
Component with harness connected
(Four Wheel Drive Control ECU)
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G54-4 (GND) - Body ground
Always
Below 1 Ω
| INSPECT CENTER CLUSTER MODULE SWITCH (REAR DIFFERENTIAL LOCK CONTROL SWITCH) |
Check the harness and connector (center cluster module switch (rear differential lock control switch) - ECU).
Disconnect the G53 ECU connector.
Disconnect the G156 switch connector.
Measure the resistance according to the value(s) in the table below.


Text in Illustration *a
Front view of wire harness connector
(to center cluster module switch (rear differential lock control switch))
*b
Front view of wire harness connector
(to Four Wheel Drive Control ECU)
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G156-15 (B) - G53-3 (R)
Always
Below 1 Ω
G156-24 (E) - Body ground
Always
Below 1 Ω
G156-24 (E) - G53-3 (R)
Always
100 kΩ or higher
Check the center cluster module switch (rear differential lock control switch).
Turn the ignition switch to ON.
Connect the G156 switch connector.
Connect the G53 ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G53-3 (R) - Body ground
center cluster module switch (rear differential lock control switch) on
Below 1.5 V
center cluster module switch (rear differential lock control switch) off
11 to 14 V
Text in Illustration *a
Component with harness connected
(Four Wheel Drive Control ECU)
| INSPECT REAR DIFFERENTIAL LOCK SHIFT ACTUATOR |
Check the harness and connector (rear differential lock actuator - ECU).
Disconnect the E1 differential lock actuator connector.
Disconnect the G53 and G54 ECU connectors.
Measure the resistance according to the value(s) in the table below.


Text in Illustration *a
Front view of wire harness connector
(to Four Wheel Drive Control ECU)
*b
Front view of wire harness connector
(to Differential Lock Shift Actuator)
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G53-10 (RLY2) - E1-5 (RLY2)
Always
Below 1 Ω
G53-10 (RLY2) - Body ground
Always
100 kΩ or higher
G53-9 (RLY1) - E1-6 (RLY1)
Always
Below 1 Ω
G53-9 (RLY1) - Body ground
Always
100 kΩ or higher
G54-5 (M2) - E1-2 (M2)
Always
Below 1 Ω
G54-5 (M2) - Body ground
Always
100 kΩ or higher
G54-1 (M1) - E1-3 (M1)
Always
Below 1 Ω
G54-1 (M1) - Body Ground
Always
100 kΩ or higher
E1-4 (GND2) - Body Ground
Always
Below 1 Ω
Check the free to lock switch.
Connect lines via a relay as shown in the illustration and check that the actuator fork moves from the free to the lock position.
- NOTICE:
- Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.
- When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.
- Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.
- HINT:
- When performing the operation described above, use the DEF relay.


Text in Illustration *1
DEF Relay
-
-
*a
Front view of wire harness connector
(to Differential Lock Shift Actuator)
-
-
After the free to lock switch is complete, check the limit switch.
Measure the resistance according to the value(s) in the table below.- Standard Resistance:
Tester Connection
Condition
Specified Condition
5 (RLY2) - 4 (GND2)
After free to lock switch is complete
Below 12.5 Ω
6 (RLY1) - 4 (GND2)
After free to lock switch is complete
500 kΩ or higher
Check the lock to free switch.
Connect lines via a relay as shown in the illustration and check that the actuator fork moves from the lock to the free position.
- NOTICE:
- Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.
- When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.
- Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.
- HINT:
- When performing the operation described above, use the DEF relay.


Text in Illustration *1
DEF Relay
-
-
*a
Front view of wire harness connector
(to Differential Lock Shift Actuator)
-
-
After the lock to free switch is complete, check the limit switch.
Measure the resistance according to the value(s) in the table below.- Standard Resistance:
Tester Connection
Condition
Specified Condition
5 (RLY2) - 4 (GND2)
After lock to free switch is complete
500 kΩ or higher
6 (RLY1) - 4 (GND2)
After lock to free switch is complete
Below 12.5 Ω
| INSPECT DIFFERENTIAL LOCK POSITION SWITCH |
Inspect the rear differential lock position switch.
Remove the rear differential lock position switch (Click here).
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
2 (+B) - 1 (GND)
Pushed
Below 1 Ω
Released
100 kΩ or higher
If the result is not as specified, replace the rear differential lock position switch.Text in Illustration *a
Component without harness connected
(Rear Differential Lock Position Switch)
*b
Pushed
*c
Released
Check the harness and connector (ECU - differential lock position switch).
Disconnect the E2 differential lock position switch connector.
Disconnect the G53 ECU connector.
Measure the resistance according to the value(s) in the table below.


Text in Illustration *a
Component without harness connected
(Rear Differential Lock Position Switch)
*b
Component without harness connected
(Four Wheel Drive Control ECU)
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G53-15 (RLP) - E2-2 (+B)
Always
Below 1 Ω
G53-15 (RLP) - Body ground
Always
100 kΩ or higher
E2-1 (GND) - Body ground
Always
Below 1 Ω


