14 (4) Timing Control System Malfunction
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The ECM controls the injection timing by actuating the timing control valve. The timing control valve is mounted on the injection pump and controls the internal fuel pressure of the pump through duty control.The ECM detects the injection advance angle based on TDC and NE signals.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| 14 (4) |
During and after warming up the engine, the actual injection timing is different from the target value that the ECM calculated for several seconds. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. INSPECT TIMING CONTROL VALVE |
Inspect the timing control valve (Click here).
|
|
||||
| OK | |
| 2. CHECK ECM (TCV VOLTAGE) |
Disconnect the ECM connector.

Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
C101-11 (TCV) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Rear view of wire harness connector
(to ECM)
Reconnect the ECM connector.
|
|
||||
| OK | |
| 3. CHECK ECM (TCV VOLTAGE, SIGNAL) |
Turn the ignition switch to ON.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
C101-11 (TCV) - C101-14 (E1)
Ignition switch ON
11 to 14 V
While idling, check the waveform according to the value(s) in the table below.
- OK:
Tester Connection
Condition
Specified Condition
C101-11 (TCV) - C101-14 (E1)
Idling
Correct waveform is as shown
Text in Illustration *a
Component with harness connected
(ECM)
*b
TCV Signal Waveform
|
|
||||
| OK | |
| 4. CHECK LEVEL WARNING SWITCH |
Check the level warning switch (Click here).
|
|
||||
| OK | |
| 5. CHECK FOR FUEL LEAK |
Visually check the injection pump, each injector and the fuel line for fuel leaks.
- OK:
- No leakage.
|
|
||||
| OK | ||
| ||
| 6. CHECK TIMING CONTROL VALVE (POWER SOURCE) |
Disconnect the timing control valve connector.

Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
C108-1 - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Timing control valve)
Reconnect the timing control valve connector.
|
|
||||
| OK | ||
| ||
| 7. CHECK HARNESS AND CONNECTOR (TIMING CONTROL VALVE - NO. 1 INTEGRATION RELAY (EFI)) |
Disconnect the timing control valve connector.
Disconnect the No. 1 integration relay (EFI) connector from the engine room junction block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
C108-1 - 1B-4
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
C108-1 or 1B-4 - Body ground
Always
10 kΩ or higher
Reconnect the timing control valve connector.
Reconnect the No. 1 integration relay (EFI) connector.
|
|
||||
| OK | ||
| ||
