2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

22 Engine Coolant Temperature Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The engine coolant temperature sensor senses the coolant temperature. A thermistor built into the sensor changes its resistance according to the coolant temperature. The lower the coolant temperature, the higher the thermistor resistance value, and the higher the coolant temperature, the lower the thermistor resistance value (see Fig. 1).
The engine coolant temperature sensor is connected to the ECM. The 5 V power source voltage from the ECM is applied to the engine coolant temperature sensor from terminal THW via resistor R. That is, resistor R and the engine coolant temperature sensor are connected in series. When the resistance value of the engine coolant temperature sensor changes in accordance with changes in the coolant temperature, the voltage at terminal THW also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability during cold engine operation.
G036559E07
DTC No.
DTC Detection Condition
Trouble Area
22
Open or short in the engine coolant temperature sensor circuit for 0.5 sec. or more.
  1. Open or short in engine coolant temperature sensor circuit
  2. Engine coolant temperature sensor
  3. ECM

WIRING DIAGRAM

A227814E03

INSPECTION PROCEDURE

HINT:
  1. If DTCs related to different systems that have terminal E2 as the ground terminal are stored simultaneously, there may be an open circuit between terminal E2 and body ground.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


When using intelligent tester:


1. READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

    Result 
    Result
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or higher
    B
    Value is same as actual engine coolant temperature
    C

    HINT:
    When DTC 22 is stored, the type of malfunction can be determined based on the engine coolant temperature (see below).
    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    140°C (284°F) or higher
    Short circuit



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

  1. A110531E12
    Disconnect the engine coolant temperature sensor connector.

  1. Connect terminals 1 and 2 of the engine coolant temperature sensor harness side connector.

  1. Turn the ignition switch to ON.

  1. Read the temperature value on the intelligent tester.

    OK:
    140°C (284°F) or higher

    Text in Illustration 
    *1
    Engine Coolant Temperature Sensor
    *2
    ECM
    *a
    Front view of wire harness connector
    (to Engine Coolant Temperature Sensor)

  1. Reconnect the engine coolant temperature sensor connector.



NG
Go to step 3
OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)

3. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN ECM)

  1. A110532E16
    Connect terminals THW and E2 of the ECM connector.

  1. Turn the ignition switch to ON.

  1. Read the temperature value on the intelligent tester.

    OK:
    140°C (284°F) or higher

    Text in Illustration 
    *1
    Engine Coolant Temperature Sensor
    *2
    ECM
    *a
    Component with harness connected
    (ECM)



NG
REPLACE ECM (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

4. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

  1. A076591E24
    Disconnect the engine coolant temperature sensor connector.

  1. Turn the ignition switch to ON.

  1. Read the temperature value on the intelligent tester.

    OK:
    -40°C (-40°F)

    Text in Illustration 
    *1
    Engine Coolant Temperature Sensor
    *2
    ECM

  1. Reconnect the engine coolant temperature sensor connector.



NG
Go to step 5
OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)

5. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN ECM)

  1. A110533E13
    Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Read the temperature value on the intelligent tester.

    OK:
    -40°C (-40°F)

    Text in Illustration 
    *1
    Engine Coolant Temperature Sensor
    *2
    ECM
    *a
    Rear view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.



NG
REPLACE ECM (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR


When not using intelligent tester:


1. CHECK ECM (THW VOLTAGE)

  1. A062416E90
    Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    C102-4 (THW) - C102-9 (E2)
    20°C (68°F)
    0.2 to 3.8 V
    C102-4 (THW) - C102-9 (E2)
    80°C (176°F)
    0.1 to 1.5 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)
  1. Disconnect the engine coolant temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open) :
    Tester Connection
    Condition
    Specified Condition
    C111-2 - C102-4 (THW)
    Always
    Below 1 Ω
    C111-1 - C102-9 (E2)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short) :
    Tester Connection
    Condition
    Specified Condition
    C111-2 or C102-4 (THW) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the engine coolant temperature sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← 19 (2) Accelerator Position Sensor Range / Performance Problem (from Aug 2014)22 Engine Coolant Temperature Sensor Circuit Malfunction (from Aug 2014) →