2013-2015 Land Cruiser Prado · Service Manual Suspension

C1713/13 Rear Height Control Sensor RH Circuit Malfunction

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The height control sensor changes its resistance value based on changes in vehicle height. The suspension control ECU outputs a fixed voltage of 5 V to the SHB terminal of the height control sensor. If the resistance value of the sensor changes, the voltage value of the sensor changes accordingly. The suspension control ECU then inputs the voltage value from the sensor to detect the vehicle height change.
DTC Code
DTC Detection Condition
Trouble Area
C1713/13
Either condition is met:
  1. With the ignition switch ON, a voltage of 5.5 V or higher or 4.3 V or less at the power source of the rear height control sensor RH is detected for 0.5 seconds.
  2. With the ignition switch ON, a voltage of 4.7 V or higher or 0.3 V or less at the rear height control sensor RH is detected for 1 second.
  1. Harness or connector
  2. Rear height control sensor RH
  3. Suspension control ECU
C1714/14
Either condition is met:
  1. With the ignition switch ON, a voltage of 5.5 V or higher or 4.3 V or less at the power source of the rear height control sensor LH is detected for 0.5 seconds.
  2. With the ignition switch ON, a voltage of 4.7 V or higher or 0.3 V or less at the rear height control sensor LH is detected for 1 second.
  1. Harness or connector
  2. Rear height control sensor LH
  3. Suspension control ECU

WIRING DIAGRAM

C216922E02

INSPECTION PROCEDURE

NOTICE:
When replacing the suspension control ECU, perform registration (Click here).


1. INSPECT REAR HEIGHT CONTROL SENSOR
C214173E05
Text in Illustration  
*A
for RH
*B
for LH
*1
Rear Height Control Sensor
-
-
*a
Component without harness connected
(Rear Height Control Sensor)
*b
Min. Low
*c
Normal
*d
Max. High
V100135
45°
V100136
45°
  1. Check the rear height control sensor RH (when DTC C1713/13 is output).

    1. Remove the rear height control sensor RH (Click here).

    2. Connect 3 dry cell batteries of 1.5 V in series.

    3. Connect the positive (+) end of the batteries to terminal 1 (SHB) of the height control sensor and the negative (-) end of the batteries to terminal 3 (SHG). While slowly moving the sensor link up and down, measure the voltage between terminal 2 (SHRR) and terminal 3 (SHG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      3 (SHG) - 2 (SHRR)
      Max. High (45°)
      4.4 to 4.6 V
      Normal (0°)
      2.3 to 2.6 V
      Min. Low (-45°)
      0.4 to 0.6 V

      NOTICE:
      Do not apply a voltage of 5 V or higher.

  1. Check the rear height control sensor LH (when DTC C1714/14 is output).

    1. Remove the rear height control sensor LH (Click here).

    2. Connect 3 dry cell batteries of 1.5 V in series.

    3. Connect the positive (+) end of the batteries to terminal 1 (SHB) of the height control sensor and the negative (-) end of the batteries to terminal 3 (SHG). While slowly moving the sensor link up and down, measure the voltage between terminal 2 (SHRL) and terminal 3 (SHG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      3 (SHG) - 2 (SHRL)
      Max. High (45°)
      4.4 to 4.6 V
      Normal (0°)
      2.3 to 2.6 V
      Min. Low (-45°)
      0.4 to 0.6 V

      NOTICE:
      Do not apply a voltage of 5 V or higher.

Result 
Result
Proceed to
OK
A
NG (Rear height control sensor RH)
B
NG (Rear height control sensor LH)
C


B
REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH (Click here)

C
REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (Click here)
A


2. CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR - SUSPENSION CONTROL ECU)
  1. Check the rear height control sensor RH (when DTC C1713/13 is output).

    1. Disconnect the S3 rear height control sensor RH connector.

    2. Disconnect the R19 suspension control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      S3-3 (SHG) - R19-16 (SGR2)
      Always
      Below 1 Ω
      S3-2 (SHRR) - R19-26 (SHRR)
      Always
      Below 1 Ω
      S3-1 (SHB) - R19-13 (SBR2)
      Always
      Below 1 Ω
      S3-3 (SHG) - Body ground
      Always
      10 kΩ or higher
      S3-2 (SHRR) - Body ground
      Always
      10 kΩ or higher
      S3-1 (SHB) - Body ground
      Always
      10 kΩ or higher

  1. Check the rear height control sensor LH (when DTC C1714/14 is output).

    1. Disconnect the S6 rear height control sensor LH connector.

    2. Disconnect the R19 suspension control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      S6-3 (SHG) - R19-15 (SGL2)
      Always
      Below 1 Ω
      S6-2 (SHRL) - R19-24 (SHRL)
      Always
      Below 1 Ω
      S6-1 (SHB) - R19-14 (SBL2)
      Always
      Below 1 Ω
      S6-3 (SHG) - Body ground
      Always
      10 kΩ or higher
      S6-2 (SHRL) - Body ground
      Always
      10 kΩ or higher
      S6-1 (SHB) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SUSPENSION CONTROL ECU (Click here)


← ON-VEHICLE INSPECTION (from Aug 2013)C1713/13 Rear Height Control Sensor RH Circuit Malfunction (+ C1714/14) (from Aug 2014) →