C1713/13 Rear Height Control Sensor RH Circuit Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2014
Also covers:
- C1714/14 Rear Height Control Sensor LH Circuit Malfunction
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The height control sensor changes its resistance value based on changes in vehicle height. The suspension control ECU outputs a fixed voltage of 5 V to the SHB terminal of the height control sensor. If the resistance value of the sensor changes, the voltage value of the sensor changes accordingly. The suspension control ECU then inputs the voltage value from the sensor to detect the vehicle height change.| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1713/13 |
Either condition is met:
|
|
| C1714/14 |
Either condition is met:
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the suspension control ECU, perform registration (Click here).
| 1. INSPECT REAR HEIGHT CONTROL SENSOR |


| *A |
for RH |
*B |
for LH |
| *1 |
Rear Height Control Sensor |
- |
- |
| *a |
Component without harness connected (Rear Height Control Sensor) |
*b |
Min. Low |
| *c |
Normal |
*d |
Max. High |
![]() ![]() |
45° |
![]() ![]() |
45° |
Check the rear height control sensor RH (when DTC C1713/13 is output).
Remove the rear height control sensor RH (Click here).
Connect 3 dry cell batteries of 1.5 V in series.
Connect the positive (+) end of the batteries to terminal 1 (SHB) of the height control sensor and the negative (-) end of the batteries to terminal 3 (SHG). While slowly moving the sensor link up and down, measure the voltage between terminal 2 (SHRR) and terminal 3 (SHG).
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
3 (SHG) - 2 (SHRR)
Max. High (45°)
4.4 to 4.6 V
Normal (0°)
2.3 to 2.6 V
Min. Low (-45°)
0.4 to 0.6 V
- NOTICE:
- Do not apply a voltage of 5 V or higher.
Check the rear height control sensor LH (when DTC C1714/14 is output).
Remove the rear height control sensor LH (Click here).
Connect 3 dry cell batteries of 1.5 V in series.
Connect the positive (+) end of the batteries to terminal 1 (SHB) of the height control sensor and the negative (-) end of the batteries to terminal 3 (SHG). While slowly moving the sensor link up and down, measure the voltage between terminal 2 (SHRL) and terminal 3 (SHG).
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
3 (SHG) - 2 (SHRL)
Max. High (45°)
4.4 to 4.6 V
Normal (0°)
2.3 to 2.6 V
Min. Low (-45°)
0.4 to 0.6 V
- NOTICE:
- Do not apply a voltage of 5 V or higher.
| Result |
Proceed to |
| OK |
A |
| NG (Rear height control sensor RH) |
B |
| NG (Rear height control sensor LH) |
C |
|
|
||||
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR - SUSPENSION CONTROL ECU) |
Check the rear height control sensor RH (when DTC C1713/13 is output).
Disconnect the S3 rear height control sensor RH connector.
Disconnect the R19 suspension control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
S3-3 (SHG) - R19-16 (SGR2)
Always
Below 1 Ω
S3-2 (SHRR) - R19-26 (SHRR)
Always
Below 1 Ω
S3-1 (SHB) - R19-13 (SBR2)
Always
Below 1 Ω
S3-3 (SHG) - Body ground
Always
10 kΩ or higher
S3-2 (SHRR) - Body ground
Always
10 kΩ or higher
S3-1 (SHB) - Body ground
Always
10 kΩ or higher
Check the rear height control sensor LH (when DTC C1714/14 is output).
Disconnect the S6 rear height control sensor LH connector.
Disconnect the R19 suspension control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
S6-3 (SHG) - R19-15 (SGL2)
Always
Below 1 Ω
S6-2 (SHRL) - R19-24 (SHRL)
Always
Below 1 Ω
S6-1 (SHB) - R19-14 (SBL2)
Always
Below 1 Ω
S6-3 (SHG) - Body ground
Always
10 kΩ or higher
S6-2 (SHRL) - Body ground
Always
10 kΩ or higher
S6-1 (SHB) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||


