2013-2015 Land Cruiser Prado · Service Manual Suspension

C1792/92 Height Control Switch Circuit (Test Mode DTC)

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The vehicle height can be adjusted by pressing the height control switch.
By pressing the "up" side, vehicle height is raised.
By pressing the "down" side, vehicle height is lowered.
DTC Code
DTC Detection Condition
Trouble Area
C1792/92
The height control switch signal does not change.
  1. Height control switch (Center cluster module switch)
  2. Harness or connector
  3. Suspension control ECU

HINT:
This DTC is stored only during test mode.


WIRING DIAGRAM

C218601E03

INSPECTION PROCEDURE

NOTICE:
When replacing the suspension control ECU, perform registration (Click here).


1. READ VALUE USING INTELLIGENT TESTER (HEIGHT CONTROL SWITCH)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / Air suspension / Data List.

    Air Suspension 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Height Control Switch (UP)
    Height control switch ("up" side) / ON or OFF
    ON: Switch is pressed and held
    OFF: Switch is not pressed
    -
    Height Control Switch (DOWN)
    Height control switch ("down" side) / ON or OFF
    ON: Switch is pressed and held
    OFF: Switch is not pressed
    -

  1. Check that the value displayed on the intelligent tester changes by pressing the height control switch "up" side or "down" side.

    OK:
    Height control switch value changes.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. INSPECT CENTER CLUSTER MODULE SWITCH
  1. Turn the ignition switch off.

  1. Remove the height control switch (center cluster module switch) (Click here).

  1. C296052E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    7 (LO) - 24 (E)
    "Down" pressed
    Below 1 Ω
    7 (LO) - 24 (E)
    "Up" pressed
    10 kΩ or higher
    6 (HI) - 24 (E)
    "Down" pressed
    10 kΩ or higher
    6 (HI) - 24 (E)
    "Up" pressed
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Height Control Switch (Center Cluster Module Switch))



NG
REPLACE CENTER CLUSTER MODULE SWITCH (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE SWITCH - SUSPENSION CONTROL ECU)
  1. Disconnect the G156 height control switch (center cluster module switch) connector.

  1. Disconnect the A49 suspension control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G156-6 (HI) - A49-15 (UPSW)
    Always
    Below 1 Ω
    G156-7 (LO) - A49-14 (DNSW)
    Always
    Below 1 Ω
    G156-24 (E) - Body ground
    Always
    Below 1 Ω
    G156-6 (HI) or A49-15 (UPSW) - Body ground
    Always
    10 kΩ or higher
    G156-7 (LO) or A49-14 (DNSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SUSPENSION CONTROL ECU (Click here)


← C1791/91 Adaptive Variable Suspension (AVS) Switch Circuit (Test Mode DTC) (from Aug 2014)C1792/92 Height Control Switch Circuit (Test Mode DTC) (from Aug 2014) →