2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Interior Light Switch Signal Circuit

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The main body ECU detects the condition of the interior light switch.

WIRING DIAGRAM

E284569E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (ROOM LIGHT SWITCH)
  1. Using the intelligent tester, read the Data List (Click here).

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Lounge Illumination Value SW (UP)
    Room light switch (up) signal / ON or OFF
    ON: Room light switch (up) on
    OFF: Room light switch (up) off
    -
    Lounge Illumination Value SW (Dwn)
    Room light switch (down) signal / ON or OFF
    ON: Room light switch (down) on
    OFF: Room light switch (down) off
    -

    OK:
    Switch condition is displayed.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT ROOM LIGHT SWITCH ASSEMBLY

  1. E198481E02
    Remove the room light switch (Click here).

  1. Measure the resistance according to the value(s) in the table.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (UP) - 4 (E)
    Room light switch up
    Below 1 Ω
    Room light switch off
    10 kΩ or higher
    2 (DOWN) - 4 (E)
    Room light switch down
    Below 1 Ω
    Room light switch off
    10 kΩ or higher



NG
REPLACE ROOM LIGHT SWITCH ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (ROOM LIGHT SWITCH ASSEMBLY - MAIN BODY ECU, DRIVER SIDE JUNCTION BLOCK AND BODY GROUND)
  1. Disconnect the G124 room light switch connector.

  1. Disconnect the 2D driver side junction block connector.

  1. Disconnect the G63 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G124-3 (UP) - G63-5 (ILUP)
    Always
    Below 1 Ω
    G124-2 (DOWN) - 2D-13
    Always
    Below 1 Ω
    G124-4 (E) - Body ground
    Always
    Below 1 Ω
    G124-3 (UP) or G63-5 (ILUP) - Body ground
    Always
    10 kΩ or higher
    G124-2 (DOWN) or 2D-13 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY
E284598E01
  1. Disconnect the 2D driver side junction block connector.

  1. Remove the main body ECU (Click here).

  1. Measure the resistance according to the value(s) in the table.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2D-13 - A-18 (ILDN)
    Always
    Below 1 Ω
    2D-13 - Body ground
    Always
    10 kΩ or higher

Text in Illustration 
*a
Front view of wire harness connector
(to Driver Side Junction Block Assembly)
*b
Front view of wire harness connector
(to Main Body ECU)


NG
REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)


← Back Door Courtesy Switch Circuit (from Aug 2014)Interior Light Switch Signal Circuit (from Aug 2014) →