TERMINALS OF ECU
System information · Vehicles built from Aug 2013
| CHECK SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) |


Disconnect the W2 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
- HINT:
- Measure the values on the wire harness side with the connector disconnected.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
W2-1 (B) - W2-2 (E)
W - W-B
Battery power supply
Always
11 to 14 V
W2-5 (IG) - W2-2 (E)
L - W-B
IG power supply
Ignition switch off
Below 1 V
W2-5 (IG) - W2-2 (E)
L - W-B
IG power supply
Ignition switch ON
11 to 14 V
W2-2 (E) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the W2 ECU connector.
Measure the voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
W2-7 (OPN) - W2-2 (E)
LG - W-B
Sliding roof motor open
Ignition switch ON, sliding roof closed
Slide open switch off
11 to 14 V
W2-7 (OPN) - W2-2 (E)
LG - W-B
Sliding roof motor open
Ignition switch ON, sliding roof closed
Slide open switch on
Below 1 V
W2-9 (CLS) - W2-2 (E)
B - W-B
Sliding roof motor close
Ignition switch ON, sliding roof open
Slide close switch off
11 to 14 V
W2-9 (CLS) - W2-2 (E)
B - W-B
Sliding roof motor close
Ignition switch ON, sliding roof open
Slide close switch on
Below 1 V
W2-10 (UP) - W2-2 (E)
R - W-B
Sliding roof motor up
Ignition switch ON, sliding roof tilted downward
Tilt up switch off
11 to 14 V
W2-10 (UP) - W2-2 (E)
R - W-B
Sliding roof motor up
Ignition switch ON, sliding roof tilted downward
Tilt up switch on
Below 1 V
W2-8 (DWN) - W2-2 (E)
P - W-B
Sliding roof motor down
Ignition switch ON, sliding roof tilted upward
Tilt down switch off
11 to 14 V
W2-8 (DWN) - W2-2 (E)
P - W-B
Sliding roof motor down
Ignition switch ON, sliding roof tilted upward
Tilt down switch on
Below 1 V
- If the result is not as specified, the sliding roof drive gear sub-assembly may have a malfunction.
- If the result is not as specified, the sliding roof drive gear sub-assembly may have a malfunction.
| CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |


| *A |
for LHD |
*B |
for RHD |
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (Click here).
Measure the voltage and resistance according to the value(s) in the table below.
- HINT:
- Measure the values on the wire harness side with the connector disconnected.
If the result is not as specified, there may be a malfunction in the wire harness.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A-30 (BECU) - Body ground
-
Battery power supply
Always
11 to 14 V
A-31 (ALTB) - Body ground
-
Battery power supply
Always
11 to 14 V
A-32 (IG) - Body ground
-
Ignition switch power supply
Ignition switch ON
11 to 14 V
A-32 (IG) - Body ground
-
Ignition switch power supply
Ignition switch off
Below 1 V
A-29 (ACC) - Body ground
-
ACC power supply
Ignition switch ACC
11 to 14 V
A-29 (ACC) - Body ground
-
ACC power supply
Ignition switch off
Below 1 V
A-11 (GND1) - Body ground
-
Ground
Always
Below 1 Ω
G63-3 (GND2) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
Install the main body ECU (multiplex network body ECU).
Measure the voltage according to the value(s) in the table below.
for LHD: Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
2I-27 (FLCY) - Body ground
R - Body ground
Front door LH courtesy switch input
Front door LH open
Below 1 V
2I-27 (FLCY) - Body ground
R - Body ground
Front door LH courtesy switch input
Front door LH closed
11 to 14 V
G64-11 (L2) - Body ground
GR - Body ground
Driver side door key-linked lock input
Driver side door key cylinder in lock position
Below 1 V
G64-11 (L2) - Body ground
GR - Body ground
Driver side door key-linked lock input
Ignition switch off, all doors closed and driver side door key cylinder in neutral position
Pulse generation (See waveform 1 or 2)
G64-24 (UL3) - Body ground
LG - Body ground
Driver side door key-linked unlock input
Driver side door key cylinder in unlock position
Below 1 V
G64-24 (UL3) - Body ground
LG - Body ground
Driver side door key-linked unlock input
Ignition switch off, all doors closed and driver side door key cylinder in neutral position
Pulse generation (See waveform 3 or 4)
G64-26 (RDA) - Body ground*
P - Body ground
Door control receiver input
No key in ignition key cylinder, all doors closed and transmitter switch off → on
Pulse generation
for RHD: Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
2H-26 (FRCY) - Body ground
B - Body ground
Front door RH courtesy switch input
Front door RH open
Below 1 V
2H-26 (FRCY) - Body ground
B - Body ground
Front door RH courtesy switch input
Front door RH closed
11 to 14 V
G64-11 (L2) - Body ground
GR - Body ground
Driver side door key-linked lock input
Driver side door key cylinder in lock position
Below 1 V
G64-11 (L2) - Body ground
GR - Body ground
Driver side door key-linked lock input
Ignition switch off, all doors closed and driver side door key cylinder in neutral position
Pulse generation (See waveform 1 or 2)
G64-24 (UL3) - Body ground
LG - Body ground
Driver side door key-linked unlock input
Driver side door key cylinder in unlock position
Below 1 V
G64-24 (UL3) - Body ground
LG - Body ground
Driver side door key-linked unlock input
Ignition switch off, all doors closed and driver side door key cylinder in neutral position
Pulse generation (See waveform 3 or 4)
G64-26 (RDA) - Body ground*
P - Body ground
Door control receiver input
No key in ignition key cylinder, all doors closed and transmitter switch off → on
Pulse generation
- *: w/o Entry and Start System
- *: w/o Entry and Start System
Using an oscilloscope, check waveform 1.

Waveform 1 (Reference) Item
Content
Terminal No. (Symbol)
G64-11 (L2) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Ignition switch off, all doors closed and front door key cylinder in neutral position
Using an oscilloscope, check waveform 2.

Waveform 2 (Reference) Item
Content
Terminal No. (Symbol)
G64-11 (L2) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Ignition switch off, all doors closed and front door key cylinder in neutral position
Using an oscilloscope, check waveform 3.

Waveform 3 (Reference) Item
Content
Terminal No. (Symbol)
G64-24 (UL3) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Ignition switch off, all doors closed and driver side door key cylinder in neutral position
Using an oscilloscope, check waveform 4.

Waveform 4 (Reference) Item
Content
Terminal No. (Symbol)
G64-24 (UL3) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Ignition switch off, all doors closed and driver side door key cylinder in neutral position
| CHECK CERTIFICATION ECU (w/ Smart Key System) |


Disconnect the G38 ECU connector.
Measure the voltage and resistance according to the value(s) in the table below.
- HINT:
- Measure the values on the wire harness side with the connector disconnected.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
G38-1 (+B) - G38-15 (E)
V - W-B
Battery power supply
Always
11 to 14 V
G38-15 (E) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
G38-16 (IG) - G38-15 (E)
W - W-B
IG power supply
Ignition switch off
Below 1 V
G38-16 (IG) - G38-15 (E)
W - W-B
IG power supply
Ignition switch ON
11 to 14 V
G38-17 (CUTB) - G38-15 (E)
L - W-B
Battery power supply
Always
11 to 14 V
- If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the G38 ECU connector.
Measure the voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
G39-5 (RCO) - G38-15 (E)
L - W-B
Door control receiver power source
Ignition switch off, all doors closed and transmitter switch not pressed
Below 1 V
G39-5 (RCO) - G38-15 (E)
L - W-B
Door control receiver power source
Ignition switch off, all doors closed and transmitter switch pressed
4.5 to 5.5 V
G39-15 (RDA) - G38-15 (E)
G - W-B
Door control receiver data input signal
Ignition switch off
11 to 14 V pulse generation at regular intervals
G39-16 (RSSI) - G38-15 (E)
P - W-B
Door control receiver electric wave existence signal
All doors locked, all doors closed and transmitter switch not pressed
11 to 14 V
G39-16 (RSSI) - G38-15 (E)
P - W-B
Door control receiver electric wave existence signal
All doors locked, all doors closed and transmitter switch pressed
Below 2 V
- If the result is not as specified, the certification ECU may have a malfunction.
- If the result is not as specified, the certification ECU may have a malfunction.