B1660/43 Passenger Airbag OFF Indicator Circuit Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The airbag cutoff indicator circuit consists of the center airbag sensor and the airbag cutoff indicator.The airbag cutoff indicator indicates the operation condition of the instrument panel passenger airbag, front seat side airbag and front seat outer belt.
DTC B1660/43 is stored when a malfunction is detected in the airbag cutoff indicator circuit.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B1660/43 |
One of the following conditions is met:
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
- When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
| 1. CHECK PASSENGER AIRBAG CUTOFF INDICATOR CONDITION |
Turn the ignition switch to ON.


Check the airbag cutoff indicator operation.
- HINT:
- Refer to the normal condition of the airbag cutoff indicator (Click here).
Result Result
Proceed to
Always on
A
Off
B
|
|
||||
| A | |
| 2. CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and telltale light.
- OK:
- The connectors are properly connected.
|
|
||||
| OK | |
| 3. CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor and telltale light.
Check that the connectors (on the center airbag sensor side and telltale light side) are not damaged.

- OK:
- The connectors are not deformed or damaged.
Text in Illustration *1
Telltale Light
*2
Center Airbag Sensor
|
|
||||
| OK | |
| 4. CHECK PASSENGER AIRBAG CUTOFF INDICATOR |
Connect the connector to the telltale light.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Check the airbag cutoff indicator operation.
- OK:
- The airbag cutoff indicator does not come on.
|
|
||||
| OK | |
| 5. CHECK CENTER AIRBAG SENSOR |
Connect the connectors to the center airbag sensor.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1660 is not output.
- HINT:
- Codes other than DTC B1660 may be output at this time, but they are not related to this check.
Text in Illustration *1
Telltale Light
*2
Center Airbag Sensor
|
|
||||
| OK | ||
| ||
| 6. CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - TELLTALE LIGHT) |
Turn the ignition switch off.


Text in Illustration *1
Telltale Light
*2
Center Airbag Sensor
*3
Connector C
*4
Connector B
*5
Service Wire
-
-
*a
Front view of wire harness connector
(to Telltale Light)
*b
Rear view of wire harness connector
(to Center Airbag Sensor)
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the center airbag sensor and telltale light.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G5-7 (OFF) - Body ground
Ignition switch ON
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G5-7 (OFF) - G1-17 (P-AB)
Always
Below 1 Ω
G5-7 (OFF) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 7. CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and telltale light.
- OK:
- The connectors are properly connected.
|
|
||||
| OK | |
| 8. CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor and telltale light.
Check that the connectors (on the center airbag sensor side and telltale light side) are not damaged.

- OK:
- The connectors are not deformed or damaged.
Text in Illustration *1
Telltale Light
*2
Center Airbag Sensor
|
|
||||
| OK | |
| 9. CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - TELLTALE LIGHT) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


Text in Illustration *1
Telltale Light
*2
Center Airbag Sensor
*3
Connector C
*4
Connector B
*5
Service Wire
-
-
*a
Front view of wire harness connector
(to Telltale Light)
*b
Rear view of wire harness connector
(to Center Airbag Sensor)
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G5-7 (OFF) - Body ground
Ignition switch ON
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G5-7 (OFF) - G1-17 (P-AB)
Always
Below 1 Ω
G5-7 (OFF) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | |
| 10. CHECK PASSENGER AIRBAG CUTOFF INDICATOR (SOURCE VOLTAGE) |
Turn the ignition switch off.

Connect the connectors to the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G5-5 (LAPB) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Telltale Light)
|
|
||||
| OK | |
| 11. CHECK PASSENGER AIRBAG CUTOFF INDICATOR |
Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Connect the connector to the telltale light.
Disconnect the connectors from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Check the indicator according to the value(s) in the table below.
- OK:
Tester Connection
Switch Condition
Airbag Cutoff Indicator
G1-17 (P-AB) - Body ground
Ignition switch ON
Indicator comes on
Text in Illustration *a
Rear view of wire harness connector
(to Center Airbag Sensor)
|
|
||||
| OK | |
| 12. CHECK CENTER AIRBAG SENSOR |
Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Connect the connectors to the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1660 is not output.
- HINT:
- Codes other than DTC B1660 may be output at this time, but they are not related to this check.
Text in Illustration *1
Telltale Light
*2
Center Airbag Sensor
|
|
||||
| OK | ||
| ||
