2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B1242 Wireless Door Lock Tuner Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. This DTC is stored when the applicable RDA signal cannot be received within 1 second of the PRG signal being output from the main body ECU.
DTC Code
DTC Detection Condition
Trouble Area
B1242
The applicable RDA signal cannot be received within 1 second of the PRG signal being output from the main body ECU.
  1. Harness or connector
  2. Door control receiver
  3. Main body ECU (multiplex network body ECU)

WIRING DIAGRAM

B242194E02

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. When replacing the door control receiver, refer to the registration procedures (Click here).


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B1242 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK DOOR CONTROL RECEIVER (DOOR CONTROL RECEIVER - MAIN BODY ECU)
  1. Disconnect the R26 receiver connector.

  1. Disconnect the G64 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R26-2 (RDA) - G64-26 (RDA)
    Always
    Below 1 Ω
    R26-3 (PRG) - G64-25 (PRG)
    R26-2 (RDA) or G64-26 (RDA) - Body ground
    Always
    10 kΩ or higher
    R26-3 (PRG) or G64-25 (PRG) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)

  1. B219541E05
    Disconnect the R26 receiver connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R26-1 (GND) - Body ground
    Always
    Below 1 Ω

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    R26-5 (+B) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Door Control Receiver)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE DOOR CONTROL RECEIVER
  1. Temporarily replace the door control receiver with a new one.

    1. for 5 Door: (Click here).
    2. for 3 Door: (Click here).

  1. Perform the registration procedures (Click here).


NEXT


6. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


7. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B1242 is not output.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE)


← B1242 Wireless Door Lock Tuner Circuit Malfunction (Aug 2013 – Jul 2014)Only Wireless Control Function is Inoperative (Aug 2013 – Jul 2014) →