2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

INSPECTION

Inspection · Vehicles built from Aug 2013


INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

B184438E11
Text in Illustration 
*a
Lock
*b
Unlock
*c
Component without harness connected
(Front Door Lock Assembly LH)
-
-
  1. Check the door lock motor operation.

    1. Apply battery voltage to the motor connector and check the operation of the front door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 4 (L)
      Battery negative (-) → 1 (UL)
      Lock
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 4 (L)
      Unlock

      1. If the result is not as specified, replace the front door lock assembly.

  1. Check the detection switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      8 (LSSR) - 7 (E)
      Lock
      10 kΩ or higher
      8 (LSSR) - 7 (E)
      Unlock
      Below 1 Ω

      1. If the result is not as specified, replace the front door lock assembly.

  1. for LHD:

    B184437E15

    Text in Illustration 
    *a
    Lock
    *b
    Off
    *c
    Unlock
    *d
    Component without harness connected
    (Front Door Lock Assembly LH)

    1. Check the door lock and unlock switch.

      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance:
        Tester Connection
        Switch Condition
        Specified Condition
        9 (L) - 7 (E)
        Lock
        Below 1 Ω
        9 (L) - 7 (E)
        10 (UL) - 7 (E)
        OFF
        10 kΩ or higher
        10 (UL) - 7 (E)
        Unlock
        Below 1 Ω

      1. If the result is not as specified, replace the front door lock assembly.


INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

B144111E14
Text in Illustration 
*a
Lock
*b
Unlock
*c
Component without harness connected
(Front Door Lock Assembly LH)
-
-
  1. Check the door lock motor operation.

    1. Apply battery voltage to the motor connector and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 4 (L)
      Battery negative (-) → 3 (UL)
      Lock
      Battery positive (+) → 3 (UL)
      Battery negative (-) → 4 (L)
      Unlock
      Battery positive (+) → 2 (DL)
      Battery negative (-) → 1 (UNDL)
      Set
      Battery positive (+) → 1 (UNDL)
      Battery negative (-) → 2 (DL)
      Unset

      1. If the result is not as specified, replace the front door lock assembly.

  1. Check the detection switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      8 (LSSR) - 7 (E)
      Lock
      10 kΩ or higher
      8 (LSSR) - 7 (E)
      Unlock
      Below 1 Ω

      1. If the result is not as specified, replace the front door lock assembly.

  1. for LHD:

    B144108E03

    Text in Illustration 
    *a
    Lock
    *b
    Unlock
    *c
    Component without harness connected
    (Front Door Lock Assembly LH)
    -
    -

    1. Check the door lock and unlock switch.

      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance:
        Tester Connection
        Switch Condition
        Specified Condition
        9 (L) - 7 (E)
        Lock
        Below 1 Ω
        9 (L) - 7 (E)
        10 (UL) - 7 (E)
        OFF
        10 kΩ or higher
        10 (UL) - 7 (E)
        Unlock
        Below 1 Ω

      1. If the result is not as specified, replace the front door lock assembly.


INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

B184439E11
Text in Illustration 
*a
Unlock
*b
Lock
*c
Component without harness connected
(Front Door Lock Assembly RH)
-
-
  1. Check the door lock motor operation.

    1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 4 (L)
      Battery negative (-) → 1 (UL)
      Lock
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 4 (L)
      Unlock

      1. If the result is not as specified, replace the front door lock assembly.

  1. Check the detection switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      7 (LSSR) - 8 (E)
      Lock
      10 kΩ or higher
      7 (LSSR) - 8 (E)
      Unlock
      Below 1 Ω

      1. If the result is not as specified, replace the front door lock assembly.

  1. for RHD:

    B144104E08

    Text in Illustration 
    *a
    Unlock
    *b
    Lock
    *c
    Component without harness connected
    (Front Door Lock Assembly RH)
    -
    -

    1. Check the door lock and unlock switch.

      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance:
        Tester Connection
        Switch Condition
        Specified Condition
        6 (L) - 8 (E)
        Lock
        Below 1 Ω
        6 (L) - 8 (E)
        5 (UL) - 8 (E)
        OFF
        10 kΩ or higher
        5 (UL) - 8 (E)
        Unlock
        Below 1 Ω

      1. If the result is not as specified, replace the front door lock assembly.


INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

B144110E12
Text in Illustration 
*a
Unlock
*b
Lock
*c
Component without harness connected
(Front Door Lock Assembly RH)
-
-
  1. Check the door lock motor operation.

    1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 2 (L)
      Battery negative (-) → 1 (UL)
      Lock
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 2 (L)
      Unlock
      Battery positive (+) → 4 (DL)
      Battery negative (-) → 3 (UNDL)
      Set
      Battery positive (+) → 3 (UNDL)
      Battery negative (-) → 4 (DL)
      Unset

      1. If the result is not as specified, replace the front door lock assembly.

  1. Check the detection switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      7 (LSSR) - 8 (E)
      Lock
      10 kΩ or higher
      7 (LSSR) - 8 (E)
      Unlock
      Below 1 Ω

      1. If the result is not as specified, replace the front door lock assembly.

  1. for RHD:

    B144105E05

    Text in Illustration 
    *a
    Unlock
    *b
    Lock
    *c
    Component without harness connected
    (Front Door Lock Assembly RH)
    -
    -

    1. Check the door lock and unlock switch.

      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance:
        Tester Connection
        Switch Condition
        Specified Condition
        6 (L) - 8 (E)
        Lock
        Below 1 Ω
        6 (L) - 8 (E)
        5 (UL) - 8 (E)
        OFF
        10 kΩ or higher
        5 (UL) - 8 (E)
        Unlock
        Below 1 Ω

      1. If the result is not as specified, replace the front door lock assembly.

← REMOVAL (from Aug 2014)INSTALLATION (Aug 2013 – Jul 2014) →