2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

B15C3 Speaker Output Short

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

DTC Code
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit.
  1. Radio and Display Receiver Assembly*1
  2. Stereo component amplifier assembly*2
  3. Speakers
  4. Harness or connector
  1. *1: for 6 Speakers
  2. *2: for 9 Speakers

WIRING DIAGRAM

E285156E02
E284323E07

INSPECTION PROCEDURE

HINT:
  1. After the inspection is completed, clear the DTCs.
  2. When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


1. CLEAR DTC
  1. Clear the DTC (Click here).


NEXT


2. CHECK FOR DTC
  1. Recheck for DTCs and check if the same DTC is output again (Click here).

    OK:
    DTC B15C3 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK VEHICLE CONDITION (SPEAKER TYPE)
  1. Check the vehicle condition.

    Result 
    Result
    Proceed to
    for 6 Speakers
    A
    for 9 Speakers
    B



B
Go to step 8
A


4. CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
  1. *1: for RH Side
  2. *2: for LH Side
  1. Disconnect the H48 and H49 radio and display receiver assembly connectors.

  1. Disconnect the J4*1 and/or K3*2 front No. 1 speaker assembly connector.

  1. Disconnect the H34*1 and/or H35*2 front No. 2 speaker assembly connector.

  1. for 3 Door:Disconnect the Q32*1 and/or R37*2 rear speaker set connector.

  1. for 5 Door:Disconnect the L1*1 and/or M1*2 rear speaker set connector.

    Standard Resistance:
    for 3 Door (RH Side) 
    Tester Connection
    Condition
    Specified Condition
    H49-1 (FR+) - H34-3 (TWR+)
    Always
    Below 1 Ω
    H49-5 (FR-) - H34-1 (TWR-)
    Always
    Below 1 Ω
    H34-4 (+) - J4-1
    Always
    Below 1 Ω
    H34-2 (-) - J4-2
    Always
    Below 1 Ω
    H48-1 (RR+) - Q32-1
    Always
    Below 1 Ω
    H48-3 (RR-) - Q32-2
    Always
    Below 1 Ω
    H49-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    H49-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    H34-4 (+) - Body ground
    Always
    10 kΩ or higher
    H34-2 (-) - Body ground
    Always
    10 kΩ or higher
    H48-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    H48-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    for 3 Door (LH Side) 
    Tester Connection
    Condition
    Specified Condition
    H49-2 (FL+) - H35-3 (TWL+)
    Always
    Below 1 Ω
    H49-6 (FL-) - H35-1 (TWL-)
    Always
    Below 1 Ω
    H35-4 (+) - K3-1
    Always
    Below 1 Ω
    H35-2 (-) - K3-2
    Always
    Below 1 Ω
    H48-2 (RL+) - R37-1
    Always
    Below 1 Ω
    H48-6 (RL-) - R37-2
    Always
    Below 1 Ω
    H49-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    H49-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    H35-4 (+) - Body ground*2
    Always
    10 kΩ or higher
    H35-2 (-) - Body ground*2
    Always
    10 kΩ or higher
    H48-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    H48-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    for 5 Door (RH Side) 
    Tester Connection
    Condition
    Specified Condition
    H49-1 (FR+) - H34-3 (TWR+)
    Always
    Below 1 Ω
    H49-5 (FR-) - H34-1 (TWR-)
    Always
    Below 1 Ω
    H34-4 (+) - J4-1
    Always
    Below 1 Ω
    H34-2 (-) - J4-2
    Always
    Below 1 Ω
    H48-1 (RR+) - L1-1
    Always
    Below 1 Ω
    H48-3 (RR-) - L1-2
    Always
    Below 1 Ω
    H49-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    H49-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    H34-4 (+) - Body ground
    Always
    10 kΩ or higher
    H34-2 (-) - Body ground
    Always
    10 kΩ or higher
    H48-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    H48-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    for 5 Door (LH Side) 
    Tester Connection
    Condition
    Specified Condition
    H49-2 (FL+) - H35-3 (TWL+)
    Always
    Below 1 Ω
    H49-6 (FL-) - H35-1 (TWL-)
    Always
    Below 1 Ω
    H35-4 (+) - K3-1
    Always
    Below 1 Ω
    H35-2 (-) - K3-2
    Always
    Below 1 Ω
    H48-2 (RL+) - M1-1
    Always
    Below 1 Ω
    H48-6 (RL-) - M1-2
    Always
    Below 1 Ω
    H49-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    H49-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    H35-4 (+) - Body ground*2
    Always
    10 kΩ or higher
    H35-2 (-) - Body ground*2
    Always
    10 kΩ or higher
    H48-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    H48-6 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly (Click here).

  1. Inspect the front No. 1 speaker assembly (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


6. CHECK FRONT NO. 2 SPEAKER ASSEMBLY
  1. Replace the front No. 2 speaker with a known good one (Click here).

  1. Check that the malfunction disappears.

    HINT:
    1. Connect all the connectors that were disconnected from the front No. 2 speaker assemblies.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 7
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

7. INSPECT REAR SPEAKER SET
  1. Remove the rear speaker set.

    1. for 3 Door: Click here
    2. for 5 Door: Click here

  1. Inspect the rear speaker set.

    1. for 3 Door: Click here
    2. for 5 Door: Click here

Result 
Result
Proceed to
OK
A
NG (for 3 Door)
B
NG (for 5 Door)
C


B
REPLACE REAR SPEAKER SET (Click here)

C
REPLACE REAR SPEAKER SET (Click here)
A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

8. CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
  1. *1: for RH Side
  2. *2: for LH Side
  1. Disconnect the H67 stereo component amplifier assembly connector.

  1. Disconnect the J4*1 and/or K3*2 front No. 1 speaker assembly connector.

  1. Disconnect the H10*1 and/or H13*2 front No. 2 speaker assembly connector.

  1. Disconnect the H21*1 and/or H22*2 front No. 3 speaker assembly connector.

  1. Disconnect the H14 front No. 4 speaker assembly connector.

  1. for 3 Door:Disconnect the Q32*1 and/or R37*2 rear speaker set connector.

  1. for 5 Door:Disconnect the L1*1 and/or M1*2 rear speaker set connector.

    Standard Resistance:
    for Front No. 4 Speaker Assembly 
    Tester Connection
    Condition
    Specified Condition
    H67-7 (CTR+) - H14-2
    Always
    Below 1 Ω
    H67-22 (CTR-) - H14-1
    Always
    Below 1 Ω
    H67-7 (CTR+) - Body ground
    Always
    10 kΩ or higher
    H67-22 (CTR-) - Body ground
    Always
    10 kΩ or higher
    for 3 Door (RH Side) 
    Tester Connection
    Condition
    Specified Condition
    H67-5 (WFR+) - J4-1
    Always
    Below 1 Ω
    H67-20 (WFR-) - J4-2
    Always
    Below 1 Ω
    H67-13 (FR+) - H21-1 (TWR+)
    Always
    Below 1 Ω
    H67-28 (FR-) - H21-2 (TWR-)
    Always
    Below 1 Ω
    H21-3 (+) - H10-2
    Always
    Below 1 Ω
    H21-4 (-) - H10-1
    Always
    Below 1 Ω
    H67-15 (RR+) - Q32-1
    Always
    Below 1 Ω
    H67-30 (RR-) - Q32-2
    Always
    Below 1 Ω
    H67-5 (WFR+) - Body ground
    Always
    10 kΩ or higher
    H67-20 (WFR-) - Body ground
    Always
    10 kΩ or higher
    H67-13 (FR+) - Body ground
    Always
    10 kΩ or higher
    H67-28 (FR-) - Body ground
    Always
    10 kΩ or higher
    H21-3 (+) - Body ground
    Always
    10 kΩ or higher
    H21-4 (-) - Body ground
    Always
    10 kΩ or higher
    H67-15 (RR+) - Body ground
    Always
    10 kΩ or higher
    H67-30 (RR-) - Body ground
    Always
    10 kΩ or higher
    for 3 Door (LH Side) 
    Tester Connection
    Condition
    Specified Condition
    H67-4 (WFL+) - K3-1
    Always
    Below 1 Ω
    H67-19 (WFL-) - K3-2
    Always
    Below 1 Ω
    H67-12 (FL+) - H22-1 (TWL+)
    Always
    Below 1 Ω
    H67-27 (FL-) - H22-2 (TWL-)
    Always
    Below 1 Ω
    H22-3 (+) - H13-2
    Always
    Below 1 Ω
    H22-4 (-) - H13-1
    Always
    Below 1 Ω
    H67-14 (RL+) - R37-1
    Always
    Below 1 Ω
    H67-29 (RL-) - R37-2
    Always
    Below 1 Ω
    H67-4 (WFL+) - Body ground
    Always
    10 kΩ or higher
    H67-19 (WFL-) - Body ground
    Always
    10 kΩ or higher
    H67-12 (FL+) - Body ground
    Always
    10 kΩ or higher
    H67-27 (FL-) - Body ground
    Always
    10 kΩ or higher
    H22-3 (+) - Body ground
    Always
    10 kΩ or higher
    H22-4 (-) - Body ground
    Always
    10 kΩ or higher
    H67-14 (RL+) - Body ground
    Always
    10 kΩ or higher
    H67-29 (RL-) - Body ground
    Always
    10 kΩ or higher
    for 5 Door (RH Side) 
    Tester Connection
    Condition
    Specified Condition
    H67-5 (WFR+) - J4-1
    Always
    Below 1 Ω
    H67-20 (WFR-) - J4-2
    Always
    Below 1 Ω
    H67-13 (FR+) - H21-1 (TWR+)
    Always
    Below 1 Ω
    H67-28 (FR-) - H21-2 (TWR-)
    Always
    Below 1 Ω
    H21-3 (+) - H10-2
    Always
    Below 1 Ω
    H21-4 (-) - H10-1
    Always
    Below 1 Ω
    H67-15 (RR+) - L1-1
    Always
    Below 1 Ω
    H67-30 (RR-) - L1-2
    Always
    Below 1 Ω
    H67-5 (WFR+) - Body ground
    Always
    10 kΩ or higher
    H67-20 (WFR-) - Body ground
    Always
    10 kΩ or higher
    H67-13 (FR+) - Body ground
    Always
    10 kΩ or higher
    H67-28 (FR-) - Body ground
    Always
    10 kΩ or higher
    H21-3 (+) - Body ground
    Always
    10 kΩ or higher
    H21-4 (-) - Body ground
    Always
    10 kΩ or higher
    H67-15 (RR+) - Body ground
    Always
    10 kΩ or higher
    H67-30 (RR-) - Body ground
    Always
    10 kΩ or higher
    for 5 Door (LH Side) 
    Tester Connection
    Condition
    Specified Condition
    H67-4 (WFL+) - K3-1
    Always
    Below 1 Ω
    H67-19 (WFL-) - K3-2
    Always
    Below 1 Ω
    H67-12 (FL+) - H22-1 (TWL+)
    Always
    Below 1 Ω
    H67-27 (FL-) - H22-2 (TWL-)
    Always
    Below 1 Ω
    H22-3 (+) - H13-2
    Always
    Below 1 Ω
    H22-4 (-) - H13-1
    Always
    Below 1 Ω
    H67-14 (RL+) - M1-1
    Always
    Below 1 Ω
    H67-29 (RL-) - M1-2
    Always
    Below 1 Ω
    H67-4 (WFL+) - Body ground
    Always
    10 kΩ or higher
    H67-19 (WFL-) - Body ground
    Always
    10 kΩ or higher
    H67-12 (FL+) - Body ground
    Always
    10 kΩ or higher
    H67-27 (FL-) - Body ground
    Always
    10 kΩ or higher
    H22-3 (+) - Body ground
    Always
    10 kΩ or higher
    H22-4 (-) - Body ground
    Always
    10 kΩ or higher
    H67-14 (RL+) - Body ground
    Always
    10 kΩ or higher
    H67-29 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly (Click here).

  1. Inspect the front No. 1 speaker assembly (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


10. CHECK FRONT NO. 2 SPEAKER ASSEMBLY
  1. Replace the front No. 2 speaker with a known good one (Click here).

  1. Check that the malfunction disappears.

    HINT:
    1. Connect all the connectors that were disconnected from the front No. 2 speaker assemblies.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 11
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

11. CHECK FRONT NO. 4 SPEAKER ASSEMBLY
  1. Replace the front No. 4 speaker with a known good one (Click here).

  1. Check that the malfunction disappears.

    HINT:
    Connect all the connectors that were disconnected from the front No. 4 speaker assemblies.

    OK:
    Malfunction disappears.



NG
Go to step 12
OK

END (FRONT NO. 4 SPEAKER ASSEMBLY IS DEFECTIVE)

12. CHECK FRONT NO. 3 SPEAKER ASSEMBLY
  1. Replace the front No. 3 speaker with a known good one (Click here).

  1. Check that the malfunction disappears.

    HINT:
    1. Connect all the connectors that were disconnected from the front No. 3 speaker assemblies.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 13
OK

END (FRONT NO. 3 SPEAKER ASSEMBLY IS DEFECTIVE)

13. INSPECT REAR SPEAKER SET
  1. Remove the rear speaker set.

    1. for 3 Door: Click here
    2. for 5 Door: Click here

  1. Inspect the rear speaker set.

    1. for 3 Door: Click here
    2. for 5 Door: Click here

Result 
Result
Proceed to
OK
A
NG (for 3 Door)
B
NG (for 5 Door)
C


B
REPLACE REAR SPEAKER SET (Click here)

C
REPLACE REAR SPEAKER SET (Click here)
A

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)


← B15C3 Speaker Output Short (Aug 2013 – Jul 2014)B15D3 Stereo Component Amplifier Disconnected (Aug 2013 – Jul 2014) →