2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B1422/22 Compressor Lock Sensor Circuit

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

SYSTEM DESCRIPTION

The ECM sends the engine speed signal to the air conditioning amplifier assembly via CAN communication.
The air conditioning amplifier assembly reads the difference between compressor speed and engine speed. When the difference becomes too large, the air conditioning amplifier assembly determines that the cooler compressor assembly is locked and turns the magnet clutch assembly off.
DTC Code
DTC Detection Condition
Trouble Area
B1422/22
Open or short in the compressor lock sensor circuit.
  1. Cooler compressor assembly (A/C lock sensor)
  2. Compressor drive belt
  3. Harness or connector
  4. Air conditioning amplifier assembly
  5. CAN communication system

WIRING DIAGRAM

E193114E11

INSPECTION PROCEDURE

HINT:
As DTC B1422/22 is also output when the compressor drive belt is damaged or loose, inspect the belt before performing troubleshooting.


1. CHECK CAN COMMUNICATION SYSTEM
  1. Use the intelligent tester to check if the CAN communication system is functioning normally.

    Result 
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output (for LHD with Entry and Start System)
    B
    CAN DTC is output (for LHD without Entry and Start System)
    C
    CAN DTC is output (for RHD with Entry and Start System)
    D
    CAN DTC is output (for RHD without Entry and Start System)
    E



B
GO TO CAN COMMUNICATION SYSTEM (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (Click here)

D
GO TO CAN COMMUNICATION SYSTEM (Click here)

E
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2. INSPECT COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR)

  1. E193115E01
    for 1GR-FE:Remove the cooler compressor assembly (A/C lock sensor) (Click here).

  1. for 1KD-FTV:Remove the cooler compressor assembly (A/C lock sensor) (Click here).

  1. for 2TR-FE:Remove the cooler compressor assembly (A/C lock sensor) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (SSR+) - 2 (SSR-)
    20°C (68°F)
    160 to 320 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1GR-FE)
    B
    NG (for 1KD-FTV)
    C
    NG (for 2TR-FE)
    D



B
REPLACE COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR) (Click here)

C
REPLACE COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR) (Click here)

D
REPLACE COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR) (Click here)
A


3. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - A/C LOCK SENSOR)
  1. Disconnect the G25 amplifier connector.

  1. Disconnect the C39 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G25-8 (LOCK) - C39-1 (SSR+)
    Always
    Below 1 Ω
    G25-13 (SG-2) - C39-2 (SSR-)
    Always
    Below 1 Ω
    G25-8 (LOCK) - Body ground
    Always
    10 kΩ or higher
    G25-13 (SG-2) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (When troubleshooting according to problem symptoms table)
    A
    OK (When troubleshooting according to the DTC)
    B
    NG
    C



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← B1419/19 Rear Room Temperature Sensor Circuit (from Aug 2014)B1422/22 Compressor Lock Sensor Circuit (from Aug 2014) →