REPLACEMENT
Removal / installation · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
| 1. REMOVE REAR PROPELLER SHAFT ASSEMBLY |
Remove the rear propeller shaft assembly (Click here).
| 2. REMOVE REAR DRIVE PINION NUT |
![]() ![]() |
Using SST and a hammer, loosen the staked part of the rear drive pinion nut.
- SST
- 09930-00010
Use SST to hold the companion flange.

- SST
- 09330-00021
(09330-00030)
Using a 30 mm socket wrench, remove the rear drive pinion nut.
| 3. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY |
![]() ![]() |
Using SST, remove the rear drive pinion companion flange sub-assembly.
- SST
- 09950-30012
(09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)
- NOTICE:
- Before using SST (center bolt), apply hypoid gear oil to its threads and tip.
| 4. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL |
![]() ![]() |
Using SST, remove the rear differential carrier oil seal.
- SST
- 09308-10010
Text in Illustration *1
Oil Seal
*2
Oil Slinger
| 5. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER |
Remove the rear differential drive pinion oil slinger.

| 6. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
Using SST, remove the rear drive pinion tapered roller bearing (inner).

- SST
- 09556-22010
Using SST, tap out the rear drive pinion tapered roller bearing (outer).

- SST
- 09308-55010
| 7. REMOVE DIFFERENTIAL OIL STORAGE RING |
![]() ![]() |
Using a screwdriver and hammer, tap out the differential oil storage ring.
| 8. REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER |
| 9. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER |
![]() ![]() |
Install a new rear differential drive pinion bearing spacer.
- NOTICE:
- Install the spacer so that it is facing in the correct direction.
| 10. INSTALL DIFFERENTIAL OIL STORAGE RING |
![]() ![]() |
Using SST and a hammer, tap in a new differential oil storage ring.
- SST
- 09308-14010
- NOTICE:
- Be careful not to damage the oil storage ring.
| 11. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() ![]() |
Using SST and a hammer, tap in the rear drive pinion front roller bearing (outer).
- SST
- 09308-14010
Install the rear drive pinion front roller bearing (inner).
| 12. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER |
![]() ![]() |
Install the rear differential drive pinion oil slinger.
| 13. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL |
![]() ![]() |
Apply MP grease to the lip of a new oil seal.
Using SST and a hammer, tap in the rear differential carrier oil seal.
- SST
- 09214-76011
- Standard oil seal depth:
- -0.30 to 0.30 mm (-0.0118 to 0.0118 in.)
Text in Illustration *1
Oil Seal Depth
| 14. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY |
Using SST, install the rear drive pinion companion flange sub-assembly.

- SST
- 09950-30012
(09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)
- NOTICE:
- Before using SST (center bolt), apply hypoid gear oil to its threads and tip.
Using SST to hold the companion flange in place, install the rear drive pinion nut.

- SST
- 09330-00021
(09330-00030)
- Torque:
- 457 N*m{ 4660 kgf*cm , 337 ft.*lbf }
| 15. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD |
![]() ![]() |
Using a torque wrench, measure the preload.
- Standard Preload (at Starting):
Item
Specified Condition
New bearing
0.83 to 2.18 N*m (8.64 to 22.2 kgf*cm, 7.35 to 19.3 in.*lbf)
Used bearing
0.88 to 1.98 N*m (8.97 to 20.2 kgf*cm, 7.79 to 17.5 in.*lbf)
- Total preload (at starting):
- 1.08 to 2.38 N*m (11.0 to 24.3 kgf*cm, 9.6 to 21.0 in.*lbf)
| 16. STAKE REAR DRIVE PINION NUT |
![]() ![]() |
Using a chisel and hammer, stake the rear drive pinion nut.
| 17. INSTALL REAR PROPELLER SHAFT ASSEMBLY |
Install the rear propeller shaft assembly (Click here).
| 18. INSTALL DIFFERENTIAL OIL |
Remove the differential filler plug and gasket.
Pour oil into the rear differential carrier assembly so that the oil level is within 0 to 5 mm (0 to 0.197 in.) of the bottom of the filler plug opening.

- NOTICE:
- Excessively large or small quantities of oil may cause problems.
- Standard Front Differential Capacity:
Differential Type
Oil Type and Viscosity
Specified Condition
Standard
Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
1.35 to 1.45 liters (1.43 to 1.53 US qts, 1.18 to 1.27 Imp. qts.)
- Standard Rear Differential Capacity:
Differential Type
Oil Type and Viscosity
Body Type
Specified Condition
Standard
Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
5 Door
2.65 to 2.75 liters (2.80 to 2.91 US qts, 2.33 to 2.42 Imp. qts.)
3 Door
2.15 to 2.25 liters (2.27 to 2.38 US qts, 1.89 to 1.98 Imp. qts.)
w/ Differential Lock
Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
5 Door
2.60 to 2.70 liters (2.75 to 2.85 US qts, 2.29 to 2.38 Imp. qts.)
3 Door
2.15 to 2.25 liters (2.27 to 2.38 US qts, 1.89 to 1.98 Imp. qts.)
Install a new gasket and the differential filler plug.
- Torque:
- Front differential carrier:
- 39 N*m{ 398 kgf*cm , 29 ft.*lbf }
- Rear differential carrier:
- 49 N*m{ 500 kgf*cm , 36 ft.*lbf }
Drive the vehicle and check the oil level again.
If necessary, add differential oil.
| 19. CHECK FOR DIFFERENTIAL OIL LEAKAGE |










