2013-2015 Land Cruiser Prado · Service Manual Drivetrain

REPLACEMENT

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. REMOVE REAR PROPELLER SHAFT ASSEMBLY
  1. Remove the rear propeller shaft assembly (Click here).


2. REMOVE REAR DRIVE PINION NUT

  1. C089309E01
    Using SST and a hammer, loosen the staked part of the rear drive pinion nut.
    SST
    09930-00010  

  1. B087842E02
    Use SST to hold the companion flange.
    SST
    09330-00021   (09330-00030)

  1. Using a 30 mm socket wrench, remove the rear drive pinion nut.


3. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

  1. C310114E01
    Using SST, remove the rear drive pinion companion flange sub-assembly.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.


4. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

  1. C310115E01
    Using SST, remove the rear differential carrier oil seal.
    SST
    09308-10010  
    Text in Illustration 
    *1
    Oil Seal
    *2
    Oil Slinger


5. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

  1. C216536
    Remove the rear differential drive pinion oil slinger.


6. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. C310116E01
    Using SST, remove the rear drive pinion tapered roller bearing (inner).
    SST
    09556-22010  

  1. C216535E01
    Using SST, tap out the rear drive pinion tapered roller bearing (outer).
    SST
    09308-55010  


7. REMOVE DIFFERENTIAL OIL STORAGE RING

  1. C217051
    Using a screwdriver and hammer, tap out the differential oil storage ring.


8. REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

9. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

  1. C311457
    Install a new rear differential drive pinion bearing spacer.

    NOTICE:
    Install the spacer so that it is facing in the correct direction.


10. INSTALL DIFFERENTIAL OIL STORAGE RING

  1. C216531E01
    Using SST and a hammer, tap in a new differential oil storage ring.
    SST
    09308-14010  

    NOTICE:
    Be careful not to damage the oil storage ring.


11. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. C216532E01
    Using SST and a hammer, tap in the rear drive pinion front roller bearing (outer).
    SST
    09308-14010  

  1. Install the rear drive pinion front roller bearing (inner).


12. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

  1. C216536
    Install the rear differential drive pinion oil slinger.


13. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

  1. C216533E02
    Apply MP grease to the lip of a new oil seal.

  1. Using SST and a hammer, tap in the rear differential carrier oil seal.

    SST
    09214-76011  

    Standard oil seal depth:
    -0.30 to 0.30 mm (-0.0118 to 0.0118 in.)

    Text in Illustration 
    *a
    Oil Seal Depth


14. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

  1. C310117
    Using SST, install the rear drive pinion companion flange sub-assembly.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.

  1. B087843E01
    Using SST to hold the companion flange in place, install the rear drive pinion nut.
    SST
    09330-00021   (09330-00030)

    Torque:
    457 N*m{ 4660 kgf*cm , 337 ft.*lbf } or less


15. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

  1. C089308E01
    Using a torque wrench, measure the preload.

    Standard Preload (at Starting):
    Item
    Specified Condition
    New bearing
    0.83 to 2.18 N*m (9 to 22 kgf*cm, 8 to 19 in.*lbf)
    Used bearing
    0.88 to 1.98 N*m (9 to 20 kgf*cm, 8 to 17 in.*lbf)

    If the result is not as specified, adjust the preload.


16. INSPECT TOTAL PRELOAD

  1. C089308E01
    Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Standard Drive Pinion Preload (at Starting):
    Item
    Specified Condition
    New bearing
    1.03 to 2.58 N*m (11 to 26 kgf*cm, 10 to 22 in.*lbf)
    Used bearing
    1.08 to 2.38 N*m (12 to 24 kgf*cm, 10 to 21 in.*lbf)


17. STAKE REAR DRIVE PINION NUT

C089310E01
  1. Using a chisel and hammer, stake the rear drive pinion nut.


18. INSTALL REAR PROPELLER SHAFT ASSEMBLY
  1. Install the rear propeller shaft assembly (Click here).


19. INSTALL DIFFERENTIAL OIL
  1. Remove the differential filler plug and gasket.

  1. D025304E38
    Pour oil into the rear differential carrier assembly so that the oil level is within 0 to 5 mm (0 to 0.197 in.) of the bottom of the filler plug opening.

    NOTICE:
    Excessively large or small quantities of oil may cause problems.


    Standard Front Differential Capacity:
    Differential Type
    Oil Type and Viscosity
    Specified Condition
    Standard
    Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
    1.35 to 1.45 liters (1.43 to 1.53 US qts, 1.18 to 1.27 Imp. qts.)


    Standard Rear Differential Capacity:
    Differential Type
    Oil Type and Viscosity
    Body Type
    Specified Condition
    Standard
    Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
    5 Door
    2.65 to 2.75 liters (2.80 to 2.91 US qts, 2.33 to 2.42 Imp. qts.)
    3 Door
    2.15 to 2.25 liters (2.27 to 2.38 US qts, 1.89 to 1.98 Imp. qts.)
    w/ Differential Lock
    Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
    5 Door
    2.60 to 2.70 liters (2.75 to 2.85 US qts, 2.29 to 2.38 Imp. qts.)
    3 Door
    2.15 to 2.25 liters (2.27 to 2.38 US qts, 1.89 to 1.98 Imp. qts.)

  1. Install a new gasket and the differential filler plug.

    Torque:
    Front differential carrier:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. Drive the vehicle and check the oil level again.
    If necessary, add differential oil.


20. CHECK FOR DIFFERENTIAL OIL LEAKAGE
← REPLACEMENT (Aug 2013 – Jul 2014)COMPONENTS (Aug 2013 – Jul 2014) →