2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built from Aug 2013


1. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.


2. REMOVE FRONT BUMPER COVER LOWER
  1. Remove the clip, 5 bolts and front bumper cover lower.


3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A224743
    Remove the 4 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.


4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


A223311E01
Text in Illustration 
*1
Reservoir Cap
*2
Radiator Cap
*3
Cylinder Block Drain Cock Plug
*4
Radiator Drain Cock Plug

  1. G038197E02
    Install a vinyl hose to the radiator side.
    Text in Illustration 
    *1
    Vinyl Hose

  1. G038198E02
    Install a vinyl hose to the engine side.
    Text in Illustration 
    *1
    Vinyl Hose

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap and drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the cylinder block drain cock plug and drain the coolant from the engine.


5. REMOVE FRONT BUMPER COVER
  1. Remove the front bumper cover (Click here).


6. REMOVE UPPER FRONT BUMPER RETAINER

  1. A302327
    Remove the 3 bolts and retainer.


7. REMOVE RADIATOR SIDE DEFLECTOR RH

  1. A302328
    Using a clip remover, detach the 3 claws and remove the clip. Then move the side deflector so that the radiator can be removed in the step below.


8. REMOVE RADIATOR SIDE DEFLECTOR LH

  1. A302329
    Using a clip remover, detach the 3 claws and remove the clip. Then move the side deflector so that the radiator can be removed in the step below.


9. REMOVE RADIATOR RESERVOIR

  1. A223323
    Disconnect the reservoir hose from the radiator.

  1. Remove the 3 bolts and radiator reservoir.


10. REMOVE FAN SHROUD

  1. A223324
    Detach the claw to open the flexible hose clamp.

  1. A223325
    Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the fan and generator V-belt (Click here).

  1. A223326
    Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.


11. DISCONNECT NO. 1 RADIATOR HOSE

  1. A224855
    Disconnect the No. 1 radiator hose from the radiator.


12. DISCONNECT NO. 2 RADIATOR HOSE

  1. A224856
    Disconnect the No. 2 radiator hose from the radiator.


13. DISCONNECT OIL COOLER INLET HOSE (for Automatic Transmission)

  1. A224857
    Disconnect the oil cooler inlet hose from the radiator.


14. DISCONNECT OIL COOLER OUTLET HOSE (for Automatic Transmission)
  1. Disconnect the oil cooler outlet hose from the radiator.


15. REMOVE RADIATOR ASSEMBLY

  1. A224068
    Remove the 4 bolts and radiator.


16. REMOVE NO. 1 RADIATOR SUPPORT
  1. Remove the 2 radiator supports and 2 No. 1 radiator support bushes.


17. REMOVE NO. 2 RADIATOR SUPPORT
  1. Remove the 2 radiator supports and 2 No. 1 radiator support bushes.


18. REMOVE NO. 1 RADIATOR TO SUPPORT SEAL
  1. Remove the seal from the radiator assembly.


19. REMOVE NO. 2 RADIATOR TO SUPPORT SEAL
  1. Remove the seal from the radiator assembly.

← ON-VEHICLE INSPECTION (from Aug 2013)INSTALLATION (from Aug 2013) →