2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B1449 Air Outlet Damper Control Servo Motor Circuit (Rear)

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The rear mode damper servo sub-assembly sends pulse signals to indicate the damper position to the air conditioning amplifier assembly. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the rear air outlet damper to any position, which controls the air outlet modes.
The air conditioning amplifier assembly communicates with the servo through the No. 2 air conditioning harness.

HINT:
Confirm that there are no mechanical problems because this DTC may be stored when either a damper link or damper is mechanically locked.

DTC Code
DTC Detection Condition
Trouble Area
B1449
Rear air outlet damper position does not change when the air conditioning amplifier assembly operates the rear mode damper servo sub-assembly.
  1. Rear mode damper servo sub-assembly
  2. No. 2 air conditioning harness assembly
  3. Harness or connector
  4. Air conditioning amplifier assembly

WIRING DIAGRAM

E193116E07

INSPECTION PROCEDURE


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1449 is not output
    A
    DTC B1449 is output
    B
    DTC B1449 and B1497 are output
    C



B
Go to step 2

C
GO TO B1497 (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

2. READ VALUE USING INTELLIGENT TESTER (REAR MODE DAMPER SERVO)
  1. Use the Data List to check if the rear mode damper servo sub-assembly is functioning properly (Click here).

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Outlet Servo Pulse (R)
    Rear mode damper servo sub-assembly target pulse / Min.: 0, Max.: 255
    83 (pulse): FACE
    41 (pulse): B/L
    7 (pulse): FOOT
    -
    Air Mix Servo Actual Pulse (R)
    Rear mode damper servo sub-assembly actual pulse / Min.: 0, Max.: 255
    83 (pulse): FACE
    41 (pulse): B/L
    7 (pulse): FOOT
    -

    OK:
    The display is as specified in the normal condition column.

    Result 
    Result
    Proceed to
    OK (When troubleshooting according to the DTC)
    A
    OK (When troubleshooting according to Problem Symptoms Table
    B
    Both target pulse and actual pulse do not display
    C
    Target pulse displays normally, but actual pulse does not display
    D



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

D
Go to step 4
A


3. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1449 is not output.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)

4. CHECK REAR MODE DAMPER SERVO SUB-ASSEMBLY
  1. Replace the rear mode damper servo sub-assembly (Click here).

    HINT:
    Since the rear mode damper servo sub-assembly cannot be inspected while it is removed from the vehicle, replace the rear mode damper servo sub-assembly with a new or normally functioning one.

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1449 is not output.



NG
Go to step 5
OK

END (REAR MODE DAMPER SERVO SUB-ASSEMBLY IS FAULTY)

5. CHECK AIR CONDITIONING HARNESS ASSEMBLY
  1. Temporarily replace the air conditioning harness assembly with a new or normally functioning one (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1449 is not output.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

END (AIR CONDITIONING HARNESS ASSEMBLY IS FAULTY)


← B1447 Air Mix Damper Control Servo Motor Circuit (Rear) (from Aug 2014)B1449 Air Outlet Damper Control Servo Motor Circuit (Rear) (from Aug 2014) →