2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B1497 Communication Malfunction (Bus Ic)

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The air conditioning harness assembly connects the air conditioning amplifier assembly and each servo motor. The air conditioning amplifier assembly supplies power and sends operation instructions to each servo motor through the air conditioning harness assembly. Each servo motor sends the damper position information to the air conditioning amplifier assembly.
DTC Code
DTC Detection Condition
Trouble Area
B1497/97
An open circuit or malfunction in the communication line.
  1. Recirculation damper servo sub-assembly
  2. Damper servo sub-assembly (air mix damper servo)
  3. Damper servo sub-assembly (mode damper servo)
  4. Rear air mix damper servo sub-assembly*
  5. Rear mode damper servo sub-assembly*
  6. Air conditioning harness assembly
  7. No. 2 air conditioning harness assembly*
  8. Air conditioning amplifier assembly
  9. Harness or connector
  1. *: w/ Rear Air Conditioning System

WIRING DIAGRAM

E306701E01
E302760E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK HARNESS AND CONNECTOR (POWER SOURCE)
E235522E04
*: w/ Rear Air Conditioning System
  1. Disconnect the G24* and G25 air conditioning amplifier assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G25-21 (B) - Body ground
    Always
    11 to 14 V
    G24-24 (+B2) - Body ground*
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G25-14 (GND) - Body ground
    Always
    Below 1 Ω
    G24-20 (RGND) - Body ground*
    Always
    Below 1 Ω

    Text in Illustration 
    *A
    w/ Rear Air Conditioning System
    *a
    Front view of wire harness connector
    (to Air Conditioning Amplifier Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check that the servo motor operates (Click here).

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Air Mix Servo Targ Pulse (D)
    Damper servo sub-assembly (air mix damper servo) target pulse
    Min.: 0, Max.: 255
    -
    Air Outlet Servo Pulse (D)
    Damper servo sub-assembly (mode damper servo) pulse
    Min.: 0, Max.: 255
    -
    Air Inlet Damper Targ Pulse
    Recirculation damper servo sub-assembly target pulse
    Min.: 0, Max.: 255
    -
    Rear Air Mix Servo Targ Pulse*
    Rear air mix damper servo sub-assembly target pulse
    Min.: 0, Max.: 255
    w/ Rear Air Conditioning System
    A/O Servo Pulse(Rr D)*
    Rear mode damper servo sub-assembly pulse
    Min.: 0, Max.: 255
    w/ Rear Air Conditioning System

    OK:
    Arm of the servo motor selected in the Active Test moves smoothly

  1. According to the test, proceed to the next step.

    Result 
    Result
    Proceed to
    One of the front servo motors is malfunctioning
    A
    All of the front servo motors are malfunctioning
    B
    One of the rear servo motors is malfunctioning
    C
    All of the rear servo motors are malfunctioning
    D



B
Go to step 7

C
Go to step 8

D
Go to step 11
A


3. SYSTEM CHECK
  1. According to the test, proceed to the next step.

    Result 
    Result
    Proceed to
    Only the damper servo sub-assembly (air mix damper servo) is malfunctioning
    A
    Only the damper servo sub-assembly (mode damper servo) is malfunctioning
    B
    Only the recirculation damper servo sub-assembly is malfunctioning
    C



B
Go to step 5

C
Go to step 6
A


4. CHECK DAMPER SERVO SUB-ASSEMBLY (AIR MIX DAMPER SERVO)
  1. Replace the damper servo sub-assembly (air mix damper servo) (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for DTCs.

    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 7
A

END (DAMPER SERVO SUB-ASSEMBLY [AIR MIX DAMPER SERVO] IS FAULTY)

5. CHECK DAMPER SERVO SUB-ASSEMBLY (MODE DAMPER SERVO)
  1. Replace the damper servo sub-assembly (mode damper servo) (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for DTCs.

    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 7
A

END (DAMPER SERVO SUB-ASSEMBLY [MODE DAMPER SERVO] IS FAULTY)

6. CHECK RECIRCULATION DAMPER SERVO SUB-ASSEMBLY
  1. Replace the recirculation damper servo sub-assembly (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for DTCs.

    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 7
A

END (RECIRCULATION DAMPER SERVO SUB-ASSEMBLY IS FAULTY)

7. CHECK AIR CONDITIONING HARNESS ASSEMBLY
  1. Replace the air conditioning harness assembly (Click here).

    HINT:
    Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or a known good one and check that the condition returns to normal.

  1. Check for DTCs.

    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
A

END (AIR CONDITIONING HARNESS ASSEMBLY IS FAULTY)

8. SYSTEM CHECK
  1. According to the test, proceed to the next step.

    Result 
    Result
    Proceed to
    Only the rear air mix damper servo sub-assembly is malfunctioning
    A
    Only the rear mode damper servo sub-assembly is malfunctioning
    B



B
Go to step 10
A


9. CHECK REAR AIR MIX DAMPER SERVO SUB-ASSEMBLY
  1. Replace the rear air mix damper servo sub-assembly (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for DTCs.

    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 11
A

END (REAR AIR MIX DAMPER SERVO SUB-ASSEMBLY IS FAULTY)

10. CHECK REAR MODE DAMPER SERVO SUB-ASSEMBLY
  1. Replace the rear mode damper servo sub-assembly (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for DTCs.

    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 11
A

END (REAR MODE DAMPER SERVO SUB-ASSEMBLY IS FAULTY)

11. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - NO. 2 AIR CONDITIONING HARNESS ASSEMBLY)
  1. Disconnect the Q13 No. 2 air conditioning harness assembly connector.

  1. Disconnect the G24 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G24-23 (RBBU) - Q13-4 (RBBU)
    Always
    Below 1 Ω
    G24-1 (RBUS) - Q13-3 (RBUS)
    Always
    Below 1 Ω
    G24-21 (RBUG) - Q13-2 (RBUG)
    Always
    Below 1 Ω
    G24-23 (RBBU) - Body ground
    Always
    10 kΩ or higher
    G24-1 (RBUS) - Body ground
    Always
    10 kΩ or higher
    G24-21 (RBUG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12. REPLACE NO. 2 AIR CONDITIONING HARNESS ASSEMBLY
  1. Replace the No. 2 air conditioning harness assembly (Click here).

    HINT:
    Since the No. 2 air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the No. 2 air conditioning harness assembly with a new or a known good one and check that the condition returns to normal.

  1. Check for DTCs.

    Result 
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
A

END (NO. 2 AIR CONDITIONING HARNESS ASSEMBLY IS FAULTY)


← B1449 Air Outlet Damper Control Servo Motor Circuit (Rear) (from Aug 2014)B1497 Communication Malfunction (Bus Ic) (from Aug 2014) →