2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

B2424 Headlight Leveling Motor LH Communication Malfunction

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The headlight leveling motor operates by receiving the signal from the headlight swivel ECU. The headlight swivel ECU detects the headlight leveling motor status using the signal from the headlight leveling motor.
DTC Code
DTC Detection Condition
Trouble Area
B2424
  1. Malfunction in the headlight leveling motor LH.
  2. Open or short in the headlight leveling motor LH communication circuit.
  1. Headlight leveling motor LH
  2. Headlight swivel ECU assembly
  3. Headlight unit LH
  4. Harness or connector
B2425
  1. Malfunction in the headlight leveling motor RH.
  2. Open or short in the headlight leveling motor RH communication circuit.
  1. Headlight leveling motor RH
  2. Headlight swivel ECU assembly
  3. Headlight unit RH
  4. Harness or connector

WIRING DIAGRAM

E188442E03

INSPECTION PROCEDURE


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2424 or B2425 output does not occur.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. READ VALUE USING INTELLIGENT TESTER (HEADLIGHT SWIVEL ECU)
  1. Using the intelligent tester, read the Data List (Click here).

    AFS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    +B
    IG power supply voltage value / 0 to 19.75 V
    11 to 14 V
    -

    OK:
    Power supply voltage is 11 to 14 V.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - HEADLIGHT SWIVEL ECU ASSEMBLY)
OK


3. CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - BODY GROUND)

  1. E131580E26
    Disconnect the A58 headlight swivel ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A58-22 (E1) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Headlight Swivel ECU Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - HEADLIGHT UNIT)
  1. Disconnect the A58 headlight swivel ECU assembly connector.

  1. Disconnect the A30*1 or A31*2 headlight connector.

    1. *1: for LH
    2. *2: for RH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    A58-30 (LH+) - A30-1 (LHB1)
    Always
    Below 1 Ω
    A58-3 (LHT) - A30-7 (LHM+)
    Always
    Below 1 Ω
    A58-27 (LH-) - A30-3 (LHE)
    Always
    Below 1 Ω
    A58-30 (LH+) - Body ground
    Always
    10 kΩ or higher
    A58-3 (LHT) - Body ground
    Always
    10 kΩ or higher
    A58-27 (LH-) - Body ground
    Always
    10 kΩ or higher
    for RH:
    Tester Connection
    Condition
    Specified Condition
    A58-11 (RH+) - A31-7 (RHM+)
    Always
    Below 1 Ω
    A58-4 (RHT) - A31-1 (RHB1)
    Always
    Below 1 Ω
    A58-28 (RHT) - A31-3 (RHE)
    Always
    Below 1 Ω
    A58-11 (RH+) - Body ground
    Always
    10 kΩ or higher
    A58-4 (RHT) - Body ground
    Always
    10 kΩ or higher
    A58-28 (RHT) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT HEADLIGHT UNIT
  1. for Halogen Headlight

    1. Remove the headlight unit (Click here).

  1. for LED Headlight

    1. Remove the headlight unit (Click here).

  1. E203230E06
    Disconnect the headlight leveling motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    7 (LHM+) - 2 (LHM+)
    Always
    Below 1 Ω
    6 (LHB1) - 1 (LHB1)
    Always
    Below 1 Ω
    8 (LHE) - 3 (LHE)
    Always
    Below 1 Ω
    for RH:
    Tester Connection
    Condition
    Specified Condition
    7 (RHM+) - 2 (RHM+)
    Always
    Below 1 Ω
    6 (RHB1) - 1 (RHB1)
    Always
    Below 1 Ω
    8 (RHE) - 3 (RHE)
    Always
    Below 1 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Halogen Headlight)
    B
    NG (LED Headlight)
    C
    Text in Illustration 
    *A
    for LH
    *B
    for RH



B
REPLACE HEADLIGHT UNIT (Click here)

C
REPLACE HEADLIGHT UNIT (Click here)
A


6. CHECK HEADLIGHT LEVELING MOTOR (OPERATION)
  1. for Halogen Headlight

    1. Temporarily replace the headlight leveling motor with a new or normally functioning one (Click here).

  1. for LED Headlight

    1. Temporarily replace the headlight leveling motor with a new or normally functioning one (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2424 or B2425 output does not occur.

Result 
Result
Proceed to
OK (for Halogen Headlight)
A
OK (LED Headlight)
B
NG
C


B
REPLACE HEADLIGHT LEVELING MOTOR (Click here)

C
REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY (Click here)
A

REPLACE HEADLIGHT LEVELING MOTOR (Click here)


← B2420 AFS ECU Malfunction (from Aug 2014)B2424 Headlight Leveling Motor LH Communication Malfunction (+ B2425) (from Aug 2014) →