2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

Short in CAN Bus Lines

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.
Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.
  1. Short between CAN bus lines
  2. ECM
  3. Brake actuator assembly (skid control ECU)*1
  4. Master cylinder solenoid (skid control ECU)*2
  5. Four wheel drive control ECU
  6. Certification ECU (smart key ECU assembly)
  7. Power management control ECU
  8. Power steering ECU assembly
  9. Navigation receiver assembly*3
  10. Radio and display receiver assembly*4
  11. Spiral cable sub-assembly (steering angle sensor)
  12. Yaw rate sensor assembly
  13. Center airbag sensor assembly
  14. Main body ECU (multiplex network body ECU)
  15. Combination meter assembly
  16. No. 1 junction connector
  17. No. 2 junction connector
  18. No. 3 junction connector
  19. No. 4 junction connector*1
  20. No. 5 junction connector*2
  1. *1: for 2TR-FE
  2. *2: for 1GR-FE, 1KD-FTV
  3. *3: w/ Navigation System (for Navigation Receiver Type) or Navigation System (for Built-in Memory)
  4. *4: w/ Navigation System (for Radio and Display Type) or w/o Navigation System

WIRING DIAGRAM

C294467E01
C294468E01
C294451E02

INSPECTION PROCEDURE

HINT:
Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR SHORT IN CAN BUS WIRES (DLC3 CAN BRANCH WIRE)

  1. H102621E54
    Disconnect the G94 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G48-6 (CANH) - G48-14 (CANL)
    Engine switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3. CONNECT CONNECTOR
  1. Reconnect the G94 No. 3 junction connector.


NEXT


4. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)

  1. H102621E54
    Disconnect the G97 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G48-6 (CANH) - G48-14 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 30
OK


5. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - FOUR WHEEL DRIVE CONTROL ECU)

  1. C242748E95
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G97-2 (CANH) - G97-13 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 10
OK


6. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CERTIFICATION ECU)

  1. C242748E96
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G97-3 (CANH) - G97-14 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 12
OK


7. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

  1. C242748E97
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G97-4 (CANH) - G97-15 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 14
OK


8. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

  1. C242748E98
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G97-5 (CANH) - G97-16 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 16
OK


9. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - ECM OR NO. 4 JUNCTION CONNECTOR)

  1. C242748E91
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G97-6 (CANH) - G97-17 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1GR-FE)
    B
    NG (for 1KD-FTV)
    C
    NG (for 2TR-FE)
    D



B
Go to step 18

C
Go to step 20

D
Go to step 22
A

REPLACE NO. 1 JUNCTION CONNECTOR

10. CONNECT CONNECTOR
  1. Reconnect the G97 No. 1 junction connector.


NEXT


11. CHECK FOR SHORT IN CAN BUS WIRES (FOUR WHEEL DRIVE CONTROL ECU)

  1. C213047E04
    Disconnect the G53 four wheel drive control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G53-19 (CANH) - G53-20 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Four Wheel Drive Control ECU)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO FOUR WHEEL DRIVE CONTROL ECU (CANH, CANL)
OK

REPLACE FOUR WHEEL DRIVE CONTROL ECU (Click here)

12. CONNECT CONNECTOR
  1. Reconnect the G97 No. 1 junction connector.


NEXT


13. CHECK FOR SHORT IN CAN BUS WIRES (CERTIFICATION ECU)

  1. C198479E09
    Disconnect the G38 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G38-9 (CANH) - G38-10 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Certification ECU [Smart Key ECU Assembly])



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

14. CONNECT CONNECTOR
  1. Reconnect the G97 No. 1 junction connector.


NEXT


15. CHECK FOR SHORT IN CAN BUS WIRES (POWER MANAGEMENT CONTROL ECU)

  1. C198951E19
    Disconnect the G51 power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G51-14 (CA1H) - G51-13 (CA1L)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER MANAGEMENT CONTROL ECU (CA1H, CA1L)
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)

16. CONNECT CONNECTOR
  1. Reconnect the G97 No. 1 junction connector.


NEXT


17. CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU ASSEMBLY)

  1. C212912E06
    Disconnect the G46 power steering ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G46-1 (CANH) - G46-2 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Steering ECU Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU ASSEMBLY (CANH, CANL)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)

18. CONNECT CONNECTOR
  1. Reconnect the G97 No. 1 junction connector.


NEXT


19. CHECK FOR SHORT IN CAN BUS WIRES (ECM)

  1. C289504E02
    Disconnect the G56 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G56-32 (CANH) - G56-31 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
OK

REPLACE ECM (Click here)

20. CONNECT CONNECTOR
  1. Reconnect the G97 No. 1 junction connector.


NEXT


21. CHECK FOR SHORT IN CAN BUS WIRES (ECM)

  1. C289504E01
    Disconnect the G58 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G58-35 (CANH) - G58-36 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
OK

REPLACE ECM (Click here)

22. CONNECT CONNECTOR
  1. Reconnect the G97 No. 1 junction connector.


NEXT


23. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

  1. C242748E69
    Disconnect the A72 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-9 (CANH) - A72-20 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK


24. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - SKID CONTROL ECU)

  1. C242748E99
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-11 (CANH) - A72-22 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)



NG
Go to step 26
OK


25. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - ECM)

  1. C242748E68
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-10 (CANH) - A72-21 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)



NG
Go to step 28
OK

REPLACE NO. 4 JUNCTION CONNECTOR

26. CONNECT CONNECTOR
  1. Reconnect the A72 No. 4 junction connector.


NEXT


27. CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)

  1. C199357E10
    Disconnect the A6 brake actuator assembly (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A6-25 (CANH) - A6-14 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly [Skid Control ECU])



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)

28. CONNECT CONNECTOR
  1. Reconnect the A72 No. 4 junction connector.


NEXT


29. CHECK FOR SHORT IN CAN BUS WIRES (ECM)

  1. C289504E03
    Disconnect the G60 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G60-34 (CANH) - G60-33 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
OK

REPLACE ECM (Click here)

30. CONNECT CONNECTOR
  1. Reconnect the G97 No. 1 junction connector.


NEXT


31. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

  1. C242748E89
    Disconnect the G100 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G100-1 (CANH) - G100- 12 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK


32. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)

  1. H102621E54
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G48-6 (CANH) - G48-14 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 48
OK


33. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY)

NOTICE:
For vehicles without a navigation system (for navigation receiver type) or navigation system (for built-in memory), go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Radio and Display Receiver Assembly)".

  1. C292202E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G100-2 (CANH) - G100- 13 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 38
OK


34. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NOTICE:
For vehicles with a navigation system (for navigation receiver type) or navigation system (for built-in memory), go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Steering Angle Sensor)".

  1. C292202E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G100-2 (CANH) - G100- 13 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 40
OK


35. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)

  1. C292202E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G100-3 (CANH) - G100- 14 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 42
OK


36. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY)

  1. C292202E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G100-4 (CANH) - G100- 15 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 44
OK


37. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)

  1. C292202E04
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G100-5 (CANH) - G100- 16 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 46
OK

REPLACE NO. 2 JUNCTION CONNECTOR

38. CONNECT CONNECTOR
  1. Reconnect the G100 No. 2 junction connector.


NEXT


39. CHECK FOR SHORT IN CAN BUS WIRES (NAVIGATION RECEIVER ASSEMBLY)

  1. C235416E11
    Disconnect the H56*1 or H61*2 navigation receiver assembly connector.
    1. *1: w/o DRL OFF Switch
    2. *2: w/ DRL OFF Switch

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/o DRL OFF Switch 
    Tester Connection
    Switch Condition
    Specified Condition
    H56-9 (CANH) - H56-10 (CANL)
    Engine switch off
    54 to 69 Ω
    w/ DRL OFF Switch 
    Tester Connection
    Switch Condition
    Specified Condition
    H61-9 (CANH) - H61-10 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *A
    w/o DRL OFF Switch
    *B
    w/ DRL OFF Switch
    *a
    Front view of wire harness connector
    (to Navigation Receiver Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NAVIGATION RECEIVER ASSEMBLY (CANH, CANL)
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

40. CONNECT CONNECTOR
  1. Reconnect the G100 No. 2 junction connector.


NEXT


41. CHECK FOR SHORT IN CAN BUS WIRES (RADIO AND DISPLAY RECEIVER ASSEMBLY)

  1. C235416E10
    Disconnect the H51 radio and display receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H51-9 (CANH) - H51-10 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

42. CONNECT CONNECTOR
  1. Reconnect the G100 No. 2 junction connector.


NEXT


43. CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)

  1. C198943E12
    Disconnect the G33 spiral cable sub-assembly (steering angle sensor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G33-4 (CANH) - G33-3 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Spiral Cable Sub-assembly [Steering Angle Sensor])



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR) (Click here)

44. CONNECT CONNECTOR
  1. Reconnect the G100 No. 2 junction connector.


NEXT


45. CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE SENSOR ASSEMBLY)

  1. C210013E06
    Disconnect the G52 yaw rate sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G52-3 (CANH) - G52-2 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate Sensor Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE YAW RATE SENSOR ASSEMBLY (Click here)

46. CONNECT CONNECTOR
  1. Reconnect the G100 No. 2 junction connector.


NEXT


47. CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY)

  1. C198952E10
    Disconnect the G1 center airbag sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G1-13 (CANH) - G1-22 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

48. CONNECT CONNECTOR
  1. Reconnect the G100 No. 2 junction connector.


NEXT


49. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

  1. C242748E87
    Disconnect the G94 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G94-1 (CANH) - G94-12 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


50. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)

  1. C292202E05
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G94-3 (CANH) - G94-14 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 52
OK


51. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR OR COMBINATION METER ASSEMBLY)

  1. C242748E88
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE, 1KD-FTV 
    Tester Connection
    Switch Condition
    Specified Condition
    G94-6 (CANH) - G94-17 (CANL)
    Engine switch off
    108 to 132 Ω
    for 2TR-FE 
    Tester Connection
    Switch Condition
    Specified Condition
    G94-2 (CANH) - G94-13 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *A
    for 1GR-FE, 1KD-FTV
    *B
    for 2TR-FE
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 2TR-FE)
    B
    NG (for 1GR-FE, 1KD-FTV)
    C



B
Go to step 54

C
Go to step 56
A

REPLACE NO. 3 JUNCTION CONNECTOR

52. CONNECT CONNECTOR
  1. Reconnect the G94 No. 3 junction connector.


NEXT


53. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)

  1. C212975E07
    Disconnect the G64 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G64-14 (CANH) - G64-13 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Main Body ECU [Multiplex Network Body ECU])



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

54. CONNECT CONNECTOR
  1. Reconnect the G94 No. 3 junction connector.


NEXT


55. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)

  1. C198950E20
    Disconnect the G6 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G6-40 (CANH) - G6-39 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

56. CONNECT CONNECTOR
  1. Reconnect the G94 No. 3 junction connector.


NEXT


57. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

  1. C242748E93
    Disconnect the A73 No. 5 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A73-9 (CANH) - A73-20 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
OK


58. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - SKID CONTROL ECU)

  1. C292202E06
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A73-11 (CANH) - A73-22 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)



NG
Go to step 60
OK


59. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

  1. C242748E94
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A73-10 (CANH) - A73-21 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)



NG
Go to step 62
OK

REPLACE NO. 5 JUNCTION CONNECTOR

60. CONNECT CONNECTOR
  1. Reconnect the A73 No. 5 junction connector.


NEXT


61. CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)

  1. C208652E03
    Disconnect the A7 master cylinder solenoid (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-11 (CANH) - A7-25 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Master Cylinder Solenoid [Skid Control ECU])



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)

62. CONNECT CONNECTOR
  1. Reconnect the A73 No. 5 junction connector.


NEXT


63. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)

  1. C198950E20
    Disconnect the G6 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G6-40 (CANH) - G6-39 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)


← Short in CAN Bus Lines (Aug 2013 – Jul 2014)Short to B+ in CAN Bus Line (Aug 2013 – Jul 2014) →