2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

Short to B+ in CAN Bus Line

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

There may be a short circuit between the CAN bus lines and +B when the resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
  1. Short between CAN bus lines and +B
  2. ECM
  3. Brake actuator assembly (skid control ECU)*1
  4. Master cylinder solenoid (skid control ECU)*2
  5. Four wheel drive control ECU
  6. Certification ECU (smart key ECU assembly)
  7. Power management control ECU
  8. Power steering ECU assembly
  9. Navigation receiver assembly*3
  10. Radio and display receiver assembly*4
  11. Spiral cable sub-assembly (steering angle sensor)
  12. Yaw rate sensor assembly
  13. Center airbag sensor assembly
  14. Main body ECU (multiplex network body ECU)
  15. Combination meter assembly
  16. No. 1 junction connector
  17. No. 2 junction connector
  18. No. 3 junction connector
  19. No. 4 junction connector*1
  20. No. 5 junction connector*2
  1. *1: for 2TR-FE
  2. *2: for 1GR-FE, 1KD-FTV
  3. *3: w/ Navigation System (for Navigation Receiver Type) or Navigation System (for Built-in Memory)
  4. *4: w/ Navigation System (for Radio and Display Type) or w/o Navigation System

WIRING DIAGRAM

C294467E01
C294468E01
C294451E02

INSPECTION PROCEDURE

HINT:
Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)

  1. C201374E11
    Disconnect the G94 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G48-6 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G48-14 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3. CONNECT CONNECTOR
  1. Reconnect the G94 No. 3 junction connector.


NEXT


4. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE)

  1. C201374E11
    Disconnect the G97 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G48-6 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G48-14 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 30
OK


5. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - FOUR WHEEL DRIVE CONTROL ECU)

  1. C294654E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G97-2 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G97-13 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 10
OK


6. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - CERTIFICATION ECU)

  1. C294654E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G97-3 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G97-14 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 12
OK


7. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

  1. C294654E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G97-4 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G97-15 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 14
OK


8. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

  1. C294654E04
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G97-5 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G97-16 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 16
OK


9. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM OR NO. 4 JUNCTION CONNECTOR)

  1. C294654E05
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G97-6 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G97-17 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1GR-FE)
    B
    NG (for 1KD-FTV)
    C
    NG (for 2TR-FE)
    D



B
Go to step 18

C
Go to step 20

D
Go to step 22
A

REPLACE NO. 1 JUNCTION CONNECTOR

10. CONNECT CONNECTOR
  1. Reconnect the G97 No. 1 junction connector.


NEXT


11. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (FOUR WHEEL DRIVE CONTROL ECU)

  1. C217223E07
    Disconnect the G53 four wheel drive control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G53-19 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G53-20 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Four Wheel Drive Control ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO FOUR WHEEL DRIVE CONTROL ECU (CANH, CANL)
OK

REPLACE FOUR WHEEL DRIVE CONTROL ECU (Click here)

12. CONNECT CONNECTOR
  1. Reconnect the G97 No. 1 junction connector.


NEXT


13. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CERTIFICATION ECU)

  1. C217227E03
    Disconnect the G38 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G38-9 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G38-10 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Certification ECU [Smart Key ECU Assembly])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

14. CONNECT CONNECTOR
  1. Reconnect the G97 No. 1 junction connector.


NEXT


15. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER MANAGEMENT CONTROL ECU)

  1. C217219E05
    Disconnect the G51 power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G51-14 (CA1H) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G51-13 (CA1L) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER MANAGEMENT CONTROL ECU (CA1H, CA1L)
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)

16. CONNECT CONNECTOR
  1. Reconnect the G97 No. 1 junction connector.


NEXT


17. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY)

  1. C217222E10
    Disconnect the G46 power steering ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G46-1 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G46-2 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Steering ECU Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU ASSEMBLY (CANH, CANL)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)

18. CONNECT CONNECTOR
  1. Reconnect the G97 No. 1 junction connector.


NEXT


19. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)

  1. C217225E27
    Disconnect the G56 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G56-32 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G56-31 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to ECM)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
OK

REPLACE ECM (Click here)

20. CONNECT CONNECTOR
  1. Reconnect the G97 No. 1 junction connector.


NEXT


21. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)

  1. C217225E31
    Disconnect the G58 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G58-35 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G58-36 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to ECM)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
OK

REPLACE ECM (Click here)

22. CONNECT CONNECTOR
  1. Reconnect the G97 No. 1 junction connector.


NEXT


23. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

  1. C294654E06
    Disconnect the A72 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-9 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    A72-20 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK


24. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - SKID CONTROL ECU)

  1. C294654E07
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-11 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    A72-22 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 26
OK


25. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - ECM)

  1. C294654E08
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-10 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    A72-21 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 28
OK

REPLACE NO. 4 JUNCTION CONNECTOR

26. CONNECT CONNECTOR
  1. Reconnect the A72 No. 4 junction connector.


NEXT


27. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU)

  1. C217564E01
    Disconnect the A6 brake actuator assembly (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A6-25 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    A6-14 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly [Skid Control ECU])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)

28. CONNECT CONNECTOR
  1. Reconnect the A72 No. 4 junction connector.


NEXT


29. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)

  1. C217225E28
    Disconnect the G60 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G60-34 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G60-33 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to ECM)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
OK

REPLACE ECM (Click here)

30. CONNECT CONNECTOR
  1. Reconnect the G97 No. 1 junction connector.


NEXT


31. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

  1. C294654E09
    Disconnect the G100 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G100-1 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G100-12 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK


32. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR SIDE)

  1. C201374E11
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G48-6 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G48-14 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 48
OK


33. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY)

NOTICE:
For vehicles without a navigation system (for navigation receiver type) or navigation system (for built-in memory), go to "Check for Short to B+ in CAN Bus Wire (No. 2 Junction Connector - Radio and Display Receiver Assembly)".

  1. C294654E10
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G100-2 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G100-13 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 38
OK


34. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NOTICE:
For vehicles with a navigation system (for navigation receiver type) or navigation system (for built-in memory), go to "Check for Short to B+ in CAN Bus Wire (No. 2 Junction Connector - Steering Angle Sensor)".

  1. C294654E10
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G100-2 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G100-13 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 40
OK


35. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)

  1. C294654E11
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G100-3 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G100-14 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 42
OK


36. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY)

  1. C294654E12
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G100-4 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G100-15 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 44
OK


37. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)

  1. C294654E13
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G100-5 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G100-16 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 46
OK

REPLACE NO. 2 JUNCTION CONNECTOR

38. CONNECT CONNECTOR
  1. Reconnect the G100 No. 2 junction connector.


NEXT


39. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY)

  1. C235427E23
    Disconnect the H56*1 or H61*2 radio and display receiver assembly connector.
    1. *1: w/o DRL OFF Switch
    2. *2: w/ DRL OFF Switch

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/o DRL OFF Switch 
    Tester Connection
    Switch Condition
    Specified Condition
    H56-9 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    H56-10 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    w/ DRL OFF Switch 
    Tester Connection
    Switch Condition
    Specified Condition
    H61-9 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    H61-10 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *A
    w/o DRL OFF Switch
    *B
    w/ DRL OFF Switch
    *a
    Front view of wire harness connector
    (to Navigation Receiver Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NAVIGATION RECEIVER ASSEMBLY (CANH, CANL)
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

40. CONNECT CONNECTOR
  1. Reconnect the G100 No. 2 junction connector.


NEXT


41. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY)

  1. C235427E21
    Disconnect the H51 radio and display receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H51-9 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    H51-10 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

42. CONNECT CONNECTOR
  1. Reconnect the G100 No. 2 junction connector.


NEXT


43. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR)

  1. C217221E18
    Disconnect the G33 spiral cable sub-assembly (steering angle sensor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G33-4 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G33-3 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Spiral Cable Sub-assembly [Steering Angle Sensor])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR) (Click here)

44. CONNECT CONNECTOR
  1. Reconnect the G100 No. 2 junction connector.


NEXT


45. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (YAW RATE SENSOR ASSEMBLY)

  1. C217220E03
    Disconnect the G52 yaw rate sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G52-3 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G52-2 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate Sensor Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE YAW RATE SENSOR ASSEMBLY (Click here)

46. CONNECT CONNECTOR
  1. Reconnect the G100 No. 2 junction connector.


NEXT


47. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY)

  1. C217224E03
    Disconnect the G1 center airbag sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G1-13 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G1-22 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

48. CONNECT CONNECTOR
  1. Reconnect the G100 No. 2 junction connector.


NEXT


49. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

  1. C294654E14
    Disconnect the G94 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G94-1 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G94-12 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


50. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)

  1. C294654E15
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G94-3 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G94-14 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 52
OK


51. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR OR COMBINATION METER ASSEMBLY)

  1. C294654E45
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE, 1KD-FTV 
    Tester Connection
    Switch Condition
    Specified Condition
    G94-6 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G94-17 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    for 2TR-FE 
    Tester Connection
    Switch Condition
    Specified Condition
    G94-2 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G94-13 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *A
    for 1GR-FE, 1KD-FTV
    *B
    for 2TR-FE
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 2TR-FE)
    B
    NG (for 1GR-FE, 1KD-FTV)
    C



B
Go to step 54

C
Go to step 56
A

REPLACE NO. 3 JUNCTION CONNECTOR

52. CONNECT CONNECTOR
  1. Reconnect the G94 No. 3 junction connector.


NEXT


53. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MAIN BODY ECU)

  1. C217219E06
    Disconnect the G64 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G64-14 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G64-13 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Main Body ECU [Multiplex Network Body ECU])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

54. CONNECT CONNECTOR
  1. Reconnect the G94 No. 3 junction connector.


NEXT


55. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)

  1. C217223E08
    Disconnect the G6 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G6-40 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G6-39 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Combination Meter Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

56. CONNECT CONNECTOR
  1. Reconnect the G94 No. 3 junction connector.


NEXT


57. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

  1. C294654E17
    Disconnect the A73 No. 5 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A73-9 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    A73-20 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
OK


58. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - SKID CONTROL ECU)

  1. C294654E18
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A73-11 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    A73-22 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 60
OK


59. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

  1. C294654E19
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A73-10 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    A73-21 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 62
OK

REPLACE NO. 5 JUNCTION CONNECTOR

60. CONNECT CONNECTOR
  1. Reconnect the A73 No. 5 junction connector.


NEXT


61. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU)

  1. C217218E03
    Disconnect the A7 master cylinder solenoid (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-11 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    A7-25 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Master Cylinder Solenoid [Skid Control ECU])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)

62. CONNECT CONNECTOR
  1. Reconnect the A73 No. 5 junction connector.


NEXT


63. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)

  1. C217223E08
    Disconnect the G6 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G6-40 (CANH) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher
    G6-39 (CANL) - G48-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Combination Meter Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)


← Short in CAN Bus Lines (from Aug 2014)Short to B+ in CAN Bus Line (from Aug 2014) →