2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

Short to GND in CAN Bus Line

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

There may be a short circuit between the CAN bus lines and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
  1. Short between CAN bus lines and GND
  2. Combination meter assembly
  3. Master cylinder solenoid (skid control ECU)
  4. Main body ECU (multiplex network body ECU)
  5. Center airbag sensor assembly
  6. Spiral cable sub-assembly (steering angle sensor)
  7. Certification ECU (smart key ECU assembly)
  8. Power management control ECU
  9. Navigation receiver assembly*1
  10. Radio and display receiver assembly*2
  11. Four wheel drive control ECU
  12. Power steering ECU assembly
  13. Yaw rate sensor assembly
  14. ECM
  15. No. 1 junction connector
  16. No. 2 junction connector
  17. No. 3 junction connector
  1. *1: w/ Navigation System (for Navigation Receiver Type)
  2. *2: w/ Navigation System (for Radio and Display Type) or w/o Navigation System

WIRING DIAGRAM

C294485E01
C294474E01
C294475E01

INSPECTION PROCEDURE

HINT:
Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)

  1. C201374E12
    Disconnect the G132 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G48-6 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G48-14 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


4. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR SIDE)

  1. C201374E12
    Disconnect the G134 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G48-6 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G48-14 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 25
OK


5. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

  1. C288300E84
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-5 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G134-16 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 11
OK


6. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

  1. C288300E85
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-4 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G134-15 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 13
OK


7. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - FOUR WHEEL DRIVE CONTROL ECU)

  1. C288300E86
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-3 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G134-14 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 15
OK


8. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY)

  1. C288300E87
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-8 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G134-19 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 17
OK


9. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - CERTIFICATION ECU)

  1. C288300E88
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-6 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G134-17 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 19
OK


10. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - ECM)

  1. C288300E89
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-2 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G134-13 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1GR-FE)
    B
    NG (for 1KD-FTV)
    C



B
Go to step 21

C
Go to step 23
A

REPLACE NO. 3 JUNCTION CONNECTOR

11. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


12. CHECK FOR SHORT TO GND IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY)

  1. C217222E09
    Disconnect the G46 power steering ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G46-1 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G46-2 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Steering ECU Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU ASSEMBLY (CANH, CANL)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)

13. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


14. CHECK FOR SHORT TO GND IN CAN BUS WIRE (POWER MANAGEMENT CONTROL ECU)

  1. C217219E13
    Disconnect the G51 power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G51-14 (CA1H) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G51-13 (CA1L) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER MANAGEMENT CONTROL ECU (CA1H, CA1L)
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)

15. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


16. CHECK FOR SHORT TO GND IN CAN BUS WIRE (FOUR WHEEL DRIVE CONTROL ECU)

  1. C217223E20
    Disconnect the G53 four wheel drive control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G53-19 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G53-20 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Four Wheel Drive Control ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO FOUR WHEEL DRIVE CONTROL ECU (CANH, CANL)
OK

REPLACE FOUR WHEEL DRIVE CONTROL ECU (Click here)

17. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


18. CHECK FOR SHORT TO GND IN CAN BUS WIRE (YAW RATE SENSOR ASSEMBLY)

  1. C217220E08
    Disconnect the G52 yaw rate sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G52-3 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G52-2 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate Sensor Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE YAW RATE SENSOR ASSEMBLY (Click here)

19. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


20. CHECK FOR SHORT TO GND IN CAN BUS WIRE (CERTIFICATION ECU)

  1. C217227E05
    Disconnect the G38 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G38-9 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G38-10 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Certification ECU [Smart Key ECU Assembly])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

21. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


22. CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)

  1. C217225E29
    Disconnect the G56 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G56-32 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G56-31 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to ECM)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
OK

REPLACE ECM (Click here)

23. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


24. CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)

  1. C217225E37
    Disconnect the G58 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G58-35 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G58-36 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to ECM)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
OK

REPLACE ECM (Click here)

25. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


26. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

  1. C288300E90
    Disconnect the G132 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-1 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G132-12 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
OK


27. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


28. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE)

  1. C201374E12
    Disconnect the A72 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G48-6 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G48-14 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 35
OK


29. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)

  1. C288300E91
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-11 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    A72-22 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 31
OK


30. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

  1. C288300E92
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-10 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    A72-21 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 33
OK

REPLACE NO. 1 JUNCTION CONNECTOR

31. CONNECT CONNECTOR
  1. Reconnect the A72 No. 1 junction connector.


NEXT


32. CHECK FOR SHORT TO GND IN CAN BUS WIRE (SKID CONTROL ECU)

  1. C217218E07
    Disconnect the A7 master cylinder solenoid (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-11 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    A7-25 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Master Cylinder Solenoid [Skid Control ECU])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)

33. CONNECT CONNECTOR
  1. Reconnect the A72 No. 1 junction connector.


NEXT


34. CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)

  1. C217223E21
    Disconnect the G6 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G6-40 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G6-39 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Combination Meter Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

35. CONNECT CONNECTOR
  1. Reconnect the A72 No. 1 junction connector.


NEXT


36. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

  1. C288300E93
    Disconnect the G132 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-8 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G132-19 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK


37. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY)

NOTICE:
For vehicles without a navigation system (for navigation receiver type), go to "Check for Short to GND in CAN Bus Wire (No. 2 Junction Connector - Radio and Display Receiver Assembly)".

  1. C288300E94
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-9 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G132-20 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 42
OK


38. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NOTICE:
For vehicles with a navigation system (for navigation receiver type), go to "Check for Short to GND in CAN Bus Wire (No. 2 Junction Connector - Center Airbag Sensor Assembly)".

  1. C288300E94
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-9 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G132-20 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 44
OK


39. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)

  1. C288300E95
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-5 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G132-16 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 46
OK


40. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)

  1. C288300E96
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-7 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G132-18 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 48
OK


41. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU)

  1. C288300E97
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-2 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G132-13 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 50
OK

REPLACE NO. 2 JUNCTION CONNECTOR

42. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


43. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY)

  1. C235427E27
    Disconnect the H56 navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H56-9 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    H56-10 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Navigation Receiver Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NAVIGATION RECEIVER ASSEMBLY (CANH, CANL)
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

44. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


45. CHECK FOR SHORT TO GND IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY)

  1. C235427E20
    Disconnect the H51 radio and display receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H51-9 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    H51-10 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

46. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


47. CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY)

  1. C217224E08
    Disconnect the G1 center airbag sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G1-13 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G1-22 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

48. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


49. CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING ANGLE SENSOR)

  1. C217221E08
    Disconnect the G33 spiral cable sub-assembly (steering angle sensor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G33-4 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G33-3 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Spiral Cable Sub-assembly [Steering Angle Sensor])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR) (Click here)

50. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


51. CHECK FOR SHORT TO GND IN CAN BUS WIRE (MAIN BODY ECU)

  1. C217219E14
    Disconnect the G64 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G64-14 (CANH) - G48-4 (CG)
    Engine switch off
    200 Ω or higher
    G64-13 (CANL) - G48-4 (CG)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Main Body ECU [Multiplex Network Body ECU])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)


← Short to GND in CAN Bus Line (Aug 2013 – Jul 2014)Open in One Side of CAN Branch Line (Aug 2013 – Jul 2014) →