2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

Open in CAN Main Wire

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

There may be an open circuit in the CAN main wire and/or DLC3 CAN branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
  1. CAN main wire and connector
  2. No. 1 junction connector
  3. No. 2 junction connector
  4. No. 3 junction connector
  5. ECM
  6. Combination meter assembly
  7. DLC3 CAN branch wire or connector

WIRING DIAGRAM

C217813E01

INSPECTION PROCEDURE

HINT:
Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - DLC3)

  1. C216818E94
    Disconnect the G132 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-4 (CANH) - G48-6 (CANH)
    Engine switch off
    Below 1 Ω
    G132-15 (CANL) - G48-14 (CANL)
    Engine switch off
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - ECM)

  1. C216814E12
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-1 (CANH) - G132-12 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 5
OK


4. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

  1. C216814E63
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-8 (CANH) - G132-19 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 10
OK

REPLACE NO. 2 JUNCTION CONNECTOR

5. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


6. CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - ECM)

  1. C216814E64
    Disconnect the G134 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-2 (CANH) - G134-13 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 8
OK


7. CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

  1. C216814E65
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-1 (CANH) - G134-12 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE NO. 3 JUNCTION CONNECTOR

8. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


9. CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 3 JUNCTION CONNECTOR)

  1. C215892E08
    Disconnect the G56*1 or G58*2 ECM connector.
    1. *1: for 1GR-FE
    2. *2: for 1KD-FTV

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE 
    Tester Connection
    Switch Condition
    Specified Condition
    G56-32 (CANH) - G56-31 (CANL)
    Engine switch off
    108 to 132 Ω
    for 1KD-FTV 
    Tester Connection
    Switch Condition
    Specified Condition
    G58-35 (CANH) - G58-36 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *A
    for 1GR-FE
    *B
    for 1KD-FTV
    *a
    Rear view of wire harness connector
    (to ECM)
    Result 
    Result
    Proceed to
    OK (for 1GR-FE)
    A
    OK (for 1KD-FTV)
    B
    NG
    C



B
REPLACE ECM (Click here)

C
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 3 JUNCTION CONNECTOR)
A

REPLACE ECM (Click here)

10. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


11. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

  1. C216814E66
    Disconnect the A72 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-10 (CANH) - A72-21 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 13
OK


12. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

  1. C216814E67
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-9 (CANH) - A72-20 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE NO. 1 JUNCTION CONNECTOR

13. CONNECT CONNECTOR
  1. Reconnect the A72 No. 1 junction connector.


NEXT


14. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 1 JUNCTION CONNECTOR)

  1. C198950E11
    Disconnect the G6 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G6-40 (CANH) - G6-39 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (COMBINATION METER ASSEMBLY - NO. 1 JUNCTION CONNECTOR)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)


← Open in CAN Main Wire (Aug 2013 – Jul 2014)Short in CAN Bus Lines (Aug 2013 – Jul 2014) →