2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

Short in CAN Bus Lines

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.
Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.
  1. Short between CAN bus lines
  2. Combination meter assembly
  3. Master cylinder solenoid (skid control ECU)
  4. Main body ECU (multiplex network body ECU)
  5. Center airbag sensor assembly
  6. Spiral cable sub-assembly (steering angle sensor)
  7. Certification ECU (smart key ECU assembly)
  8. Power management control ECU
  9. Navigation receiver assembly*1
  10. Radio and display receiver assembly*2
  11. Four wheel drive control ECU
  12. Power steering ECU assembly
  13. Yaw rate sensor assembly
  14. ECM
  15. No. 1 junction connector
  16. No. 2 junction connector
  17. No. 3 junction connector
  1. *1: w/ Navigation System (for Navigation Receiver Type)
  2. *2: w/ Navigation System (for Radio and Display Type) or w/o Navigation System

WIRING DIAGRAM

C294485E01
C294474E01
C294475E01

INSPECTION PROCEDURE

HINT:
Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR SHORT IN CAN BUS WIRES (DLC3 CAN BRANCH WIRE)

  1. C201374E13
    Disconnect the G132 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G48-6 (CANH) - G48-14 (CANL)
    Engine switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


4. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR SIDE)

  1. C201374E13
    Disconnect the G134 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G48-6 (CANH) - G48-14 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 25
OK


5. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

  1. C242748E70
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-5 (CANH) - G134-16 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 11
OK


6. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

  1. C242748E71
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-4 (CANH) - G134-15 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 13
OK


7. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - FOUR WHEEL DRIVE CONTROL ECU)

  1. C242748E72
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-3 (CANH) - G134-14 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 15
OK


8. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY)

  1. C242748E76
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-8 (CANH) - G134-19 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 17
OK


9. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - CERTIFICATION ECU)

  1. C242748E73
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-6 (CANH) - G134-17 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 19
OK


10. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - ECM)

  1. C242748E66
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G134-2 (CANH) - G134-13 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1GR-FE)
    B
    NG (for 1KD-FTV)
    C



B
Go to step 21

C
Go to step 23
A

REPLACE NO. 3 JUNCTION CONNECTOR

11. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


12. CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU ASSEMBLY)

  1. C212912E06
    Disconnect the G46 power steering ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G46-1 (CANH) - G46-2 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Steering ECU Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU ASSEMBLY (CANH, CANL)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)

13. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


14. CHECK FOR SHORT IN CAN BUS WIRES (POWER MANAGEMENT CONTROL ECU)

  1. C198951E25
    Disconnect the G51 power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G51-14 (CA1H) - G51-13 (CA1L)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER MANAGEMENT CONTROL ECU (CA1H, CA1L)
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)

15. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


16. CHECK FOR SHORT IN CAN BUS WIRES (FOUR WHEEL DRIVE CONTROL ECU)

  1. C213047E04
    Disconnect the G53 four wheel drive control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G53-19 (CANH) - G53-20 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Four Wheel Drive Control ECU)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO FOUR WHEEL DRIVE CONTROL ECU (CANH, CANL)
OK

REPLACE FOUR WHEEL DRIVE CONTROL ECU (Click here)

17. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


18. CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE SENSOR ASSEMBLY)

  1. C210013E06
    Disconnect the G52 yaw rate sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G52-3 (CANH) - G52-2 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate Sensor Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE YAW RATE SENSOR ASSEMBLY (Click here)

19. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


20. CHECK FOR SHORT IN CAN BUS WIRES (CERTIFICATION ECU)

  1. C198479E40
    Disconnect the G38 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G38-9 (CANH) - G38-10 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Certification ECU [Smart Key ECU Assembly])



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

21. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


22. CHECK FOR SHORT IN CAN BUS WIRES (ECM)

  1. C289504E02
    Disconnect the G56 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G56-32 (CANH) - G56-31 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
OK

REPLACE ECM (Click here)

23. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


24. CHECK FOR SHORT IN CAN BUS WIRES (ECM)

  1. C289504E01
    Disconnect the G58 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G58-35 (CANH) - G58-36 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
OK

REPLACE ECM (Click here)

25. CONNECT CONNECTOR
  1. Reconnect the G134 No. 3 junction connector.


NEXT


26. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

  1. C242748E74
    Disconnect the G132 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-1 (CANH) - G132-12 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
OK


27. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


28. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)

  1. C201374E13
    Disconnect the A72 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G48-6 (CANH) - G48-14 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 35
OK


29. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)

  1. C242748E75
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-11 (CANH) - A72-22 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 31
OK


30. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

  1. C242748E68
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-10 (CANH) - A72-21 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 33
OK

REPLACE NO. 1 JUNCTION CONNECTOR

31. CONNECT CONNECTOR
  1. Reconnect the A72 No. 1 junction connector.


NEXT


32. CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)

  1. C208652E03
    Disconnect the A7 master cylinder solenoid (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-11 (CANH) - A7-25 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Master Cylinder Solenoid [Skid Control ECU])



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)

33. CONNECT CONNECTOR
  1. Reconnect the A72 No. 1 junction connector.


NEXT


34. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)

  1. C198950E14
    Disconnect the G6 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G6-40 (CANH) - G6-39 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

35. CONNECT CONNECTOR
  1. Reconnect the A72 No. 1 junction connector.


NEXT


36. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

  1. C242748E65
    Disconnect the G132 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-8 (CANH) - G132-19 (CANL)
    Engine switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK


37. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY)

NOTICE:
For vehicles without a navigation system (for navigation receiver type), go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Radio and Display Receiver Assembly)".

  1. C242748E77
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-9 (CANH) - G132-20 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 42
OK


38. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NOTICE:
For vehicles with a navigation system (for navigation receiver type), go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Center Airbag Sensor Assembly)".

  1. C242748E77
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-9 (CANH) - G132-20 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 44
OK


39. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)

  1. C242748E78
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-5 (CANH) - G132-16 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 46
OK


40. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)

  1. C242748E79
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-7 (CANH) - G132-18 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 48
OK


41. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU)

  1. C242748E80
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G132-2 (CANH) - G132-13 (CANL)
    Engine switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 50
OK

REPLACE NO. 2 JUNCTION CONNECTOR

42. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


43. CHECK FOR SHORT IN CAN BUS WIRES (NAVIGATION RECEIVER ASSEMBLY)

  1. C235416E12
    Disconnect the H56 navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H56-9 (CANH) - H56-10 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Navigation Receiver Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NAVIGATION RECEIVER ASSEMBLY (CANH, CANL)
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

44. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


45. CHECK FOR SHORT IN CAN BUS WIRES (RADIO AND DISPLAY RECEIVER ASSEMBLY)

  1. C235416E10
    Disconnect the H51 radio and display receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H51-9 (CANH) - H51-10 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

46. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


47. CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY)

  1. C198952E10
    Disconnect the G1 center airbag sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G1-13 (CANH) - G1-22 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

48. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


49. CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)

  1. C198943E12
    Disconnect the G33 spiral cable sub-assembly (steering angle sensor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G33-4 (CANH) - G33-3 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Spiral Cable Sub-assembly [Steering Angle Sensor])



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR) (Click here)

50. CONNECT CONNECTOR
  1. Reconnect the G132 No. 2 junction connector.


NEXT


51. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)

  1. C212975E07
    Disconnect the G64 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G64-14 (CANH) - G64-13 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Main Body ECU [Multiplex Network Body ECU])



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)


← Open in CAN Main Wire (from Aug 2014)Short in CAN Bus Lines (from Aug 2014) →