B1630/23 Rear Airbag Sensor RH Circuit Malfunction
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Also covers:
- B1635/24 Rear Airbag Sensor LH Circuit Malfunction
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The rear airbag sensor consists of the safing sensor, diagnostic circuit, lateral deceleration sensor, etc.If the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.
DTC B1630 or B1635 is stored when a malfunction is detected in the rear airbag sensor circuit.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B1630/23 |
Either condition is met:
|
|
| B1635/24 |
Either condition is met:
|
|
WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
- When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
| 1. CHECK FOR DTC |
Turn the ignition switch to ON.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
Result Result
Proceed to
DTC B1630 and B1635 are not output
A
DTC B1635 is output
B
DTC B1630 is output
C
- HINT:
- Codes other than DTC B1630 and B1635 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| C | |
| 2. CHECK REAR AIRBAG SENSOR RH |
Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the rear airbag sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 90 seconds.
Check for DTCs (Click here).
Result Result
Proceed to
DTC B1630 and B1635 are not output
A
DTC B1635 is output (for 3 door)
B
DTC B1635 is output (for 5 door)
C
DTC B1630 is output
D
- HINT:
- Codes other than DTC B1630 and B1635 may be output at this time, but they are not related to this check.
Text in Illustration *1
Rear Airbag Sensor LH
*2
Center Airbag Sensor
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.
|
|
||||
|
|
||||
|
|
||||
| D | ||
| ||
| 3. CHECK REAR AIRBAG SENSOR LH |
Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the rear airbag sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 90 seconds.
Check for DTCs (Click here).
Result Result
Proceed to
DTC B1630 and B1635 are not output
A
DTC B1630 is output (for 3 Door)
B
DTC B1630 is output (for 5 Door)
C
DTC B1635 is output
D
- HINT:
- Codes other than DTC B1630 and B1635 may be output at this time, but they are not related to this check.
Text in Illustration *1
Rear Airbag Sensor RH
*2
Center Airbag Sensor
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.
|
|
||||
|
|
||||
|
|
||||
| D | ||
| ||
