2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work. (Click here)
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE REAR NO. 1 SEAT ASSEMBLY
  1. for 60/40 Split Double-folding Seat Type LH Side:

    1. Remove the rear No. 1 seat assembly (Click here).

  1. for 60/40 Split Double-folding Seat Type RH Side:

    1. Remove the rear No. 1 seat assembly (Click here).

  1. for 60/40 Split Tumble Seat Type LH Side:

    1. Remove the rear No. 1 seat assembly (Click here).

  1. for 60/40 Split Tumble Seat Type RH Side:

    1. Remove the rear No. 1 seat assembly (Click here).

  1. for 60/40 Split Slide Walk-in Seat Type LH Side:

    1. Remove the rear No. 1 seat assembly (Click here).

  1. for 60/40 Split Slide Walk-in Seat Type RH Side:

    1. Remove the rear No. 1 seat assembly (Click here).


3. REMOVE DOOR SCUFF PLATE ASSEMBLY LH

B238732E01
  1. Put protective tape around the door scuff plate.

  1. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


4. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

B238778
  1. Remove the front door opening trim weatherstrip.


5. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover.


6. REMOVE MAT SET PLATE COVER

B240525E01

HINT:
Use the same procedure for all mat set plate covers.

  1. Using a screwdriver, detach the 2 claws and remove the mat set plate cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective tape


7. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

B240526
  1. Remove the 5 screws.

  1. Detach the 6 claws and remove the rear floor mat rear support plate.


8. REMOVE QUARTER TRIM COVER HOLE LH

B240533
  1. Detach the 2 claws and 2 guides and remove the quarter trim cover hole.


9. REMOVE REAR FLOOR CARPET ASSEMBLY

B240527
  1. Remove the rear floor carpet.


10. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

B181695

HINT:
Use the same procedure for the other No. 1 luggage compartment trim hook.

  1. Remove the luggage compartment trim hook by turning it clockwise.


11. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

B240528E01

HINT:
Use the same procedure for the other tonneau cover holder cap.

  1. Using a screwdriver, detach the 2 claws and remove the tonneau cover holder cap.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective tape


12. REMOVE FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

B240051E01

HINT:
Use the same procedure for the other front deck side trim cover.

  1. Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective tape


13. REMOVE OUTER LAP BELT COVER

B240529

HINT:
Use the same procedure for the other outer lap belt anchor cover.

  1. Detach the 3 claws and remove the outer lap belt anchor cover.


14. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

B240531
  1. Remove the bolt and disconnect the front seat outer belt floor anchor.

  1. B240534
    Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

  1. Remove the 3 bolts and 2 screws.

  1. Detach the 9 claws and 12 clips and remove the deck trim side panel.

    B240536


15. REMOVE REAR AIRBAG SENSOR LH

  1. B241938
    Remove the nut and rear airbag sensor.

  1. Disconnect the connector.

← ON-VEHICLE INSPECTION (from Aug 2014)REMOVAL (from Aug 2014) →