2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work. (Click here)
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)
  1. for Manual Seat Type LH Side:

    1. Remove the rear No. 2 seat assembly (Click here).

  1. for Power Seat Type LH Side:

    1. Remove the rear No. 2 seat assembly (Click here).

  1. for Face to Face Seat Type:

    1. Remove the rear No. 2 seat assembly (Click here).


3. REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

B238730E01

HINT:
Use the same procedure for all rear No. 1 floor step covers.

  1. Using a screwdriver, detach the 2 claws and remove the rear No. 1 floor step cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


4. REMOVE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)

B238731
  1. Remove the 2 bolts and quarter scuff plate.


5. REMOVE REAR DOOR SCUFF PLATE LH

B238733E01
  1. Put protective tape around the rear door scuff plate.

  1. Using a screwdriver, detach the 3 clips, 6 claws and 2 guides and remove the rear door scuff plate.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


6. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

B238780
  1. Remove the rear door opening trim weatherstrip.


7. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover.


8. REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)

B240044

HINT:
Use the same procedure for the other front luggage compartment trim cover.

  1. Detach the 4 claws and remove the cap.

  1. B238749E01
    Remove the bolt, luggage hold belt striker and front luggage compartment trim cover.
    Text in Illustration 
    *1
    Luggage Hold Belt Striker


9. REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat)

B238750
  1. Detach the clip and remove the No. 1 deck board.


10. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)

B238748
  1. Detach the 5 clips and 4 claws and remove the rear floor mat rear support plate.


11. REMOVE FLOOR SIDE RAIL LH (w/ Deck Rail)

B238764
  1. Remove the 3 bolts and floor side rail.


12. REMOVE FLOOR SIDE RAIL RH (w/ Deck Rail)

HINT:
Use the same procedure described for the LH side.


13. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Rear No. 2 Seat)

  1. Detach the 4 claws and remove the rear floor carpet.

    B238751E01

    Text in Illustration 
    *A
    w/o Deck Rail
    *B
    w/ Deck Rail
    *C
    for Face to Face Seat Type
    -
    -


14. REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

B238752

HINT:
Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.

  1. Detach the 3 claws and remove the rear No. 1 seat outer lap belt anchor cover.


15. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

B181695

HINT:
Use the same procedure for the other No. 1 luggage compartment trim hook.

  1. Remove the luggage compartment trim hook by turning it clockwise.


16. REMOVE NO. 1 TONNEAU COVER HOLDER CAP

B238754E01

HINT:
Use the same procedure for the other No. 1 tonneau cover holder cap.

  1. Using a screwdriver, detach the 2 claws and remove the No. 1 tonneau cover holder cap.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


17. REMOVE ASSIST GRIP PLUG (w/ Rear No. 2 Seat)

B238757E01

HINT:
Use the same procedure for all assist grip plugs.

  1. Using a screwdriver, detach the 2 claws and remove the assist grip plug.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


18. REMOVE ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat)

B238758

HINT:
Use the same procedure for the other assist grip.

  1. Remove the 2 bolts and assist grip.


19. REMOVE FRONT DECK SIDE TRIM COVER

B240051E01

HINT:
Use the same procedure for the other front deck side trim cover.

  1. Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


20. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

  1. w/o Rear No. 2 Seat:

    1. B238753
      Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

    2. B238756
      Detach the 6 claws and 2 guides and disconnect the rear seatback lock control lever base.

    3. Remove the 4 bolts and 2 screws.

    4. Detach the 5 clips and 8 claws.

    5. Pass the rear seatback lock control lever base through the deck trim side panel and remove the deck trim side panel.

      B238755

  1. w/ Rear No. 2 Seat:

    1. B238753
      Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

    2. B238759
      Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.

    3. Remove the 2 bolts and 2 screws.

    4. Detach the 4 clips and 8 claws and remove the deck trim side panel.

      B238760


21. REMOVE REAR AIRBAG SENSOR LH

  1. B238363
    Remove the nut and rear airbag sensor.

  1. Disconnect the connector.

← ON-VEHICLE INSPECTION (from Aug 2014)REMOVAL (from Aug 2014) →