2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0299 Turbocharger / Supercharger Underboost

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

HINT:
Refer to DTC P0046 (Click here).

P0299 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Accelerate vehicle with accelerator depressed halfway or more starting from a speed of 120 km/h (75 mph) or more for 2 minutes (make sure gear is fixed and does not change)
The pressure is 55 kPa below the Target Booster Pressure for 40 seconds at an engine speed of 2800 to 4400 rpm (2 trip detection logic)*1 (1 trip detection logic)*2.
  1. Turbocharger sub-assembly
  2. Extremely low battery voltage (P0560 output simultaneously)
  3. Disconnected pipe between turbo and intake manifold
  4. Disconnected manifold absolute pressure sensor hose
  5. Throttle valve stuck closed
  6. Electric EGR control valve assembly does not close
  7. Exhaust system or intake system modified (leading to increased pressure loss, etc.)
  8. Manifold absolute pressure sensor
  9. Injection system (reduction in fuel injection volume)
  10. ECM
  1. *1: Only for vehicle Euro-OBD.
  2. *2: Only for vehicle except Euro-OBD.
Related Data List 
DTC No.
Data List
P0299
  1. Target Booster Pressure
  2. MAP

HINT:
  1. If DTC P0299 is stored due to the variable nozzle being stuck open, the following symptoms may appear:
    1. Lack of power
    2. Vehicle surge or hesitation under light or medium load


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Comparison of the data list items manifold absolute pressure and target booster pressure during acceleration under medium to high engine speeds can be used to determine the state of the problem.


1. CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0299)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0299 is output
    A
    P0299 and other DTCs are output
    B



B
GO TO DTC CHART (Click here)
A


2. CHECK INTAKE AND EXHAUST SYSTEM
  1. Check for intake and exhaust system modifications.

    OK:
    No modifications.



NG
REPAIR OR REPLACE INTAKE AND EXHAUST SYSTEM
OK


3. INSPECT TURBOCHARGER SUB-ASSEMBLY
  1. Check the turbocharger sub-assembly (Click here).

    HINT:
    Check if the VN is stuck, if there are abnormal noises from the turbo (impeller is damaged), if there is turbo shaft rattle, and if the turbo shaft does not rotate smoothly.



NG
REPLACE TURBOCHARGER SUB-ASSEMBLY (Click here)
OK


4. CHECK CONNECTION OF VACUUM HOSE
  1. Check the vacuum hoses connected to the manifold absolute pressure sensor.



NG
REPAIR OR REPLACE VACUUM HOSE
OK


5. READ VALUE USING INTELLIGENT TESTER (MAP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / MAP.

  1. Read the value.

    Standard Value:
    Condition
    Standard Value
    Idling
    90 to 102 kPa
    3000 rpm
    100 to 150 kPa



NG
REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
OK


6. READ VALUE USING INTELLIGENT TESTER (ACTUAL THROTTLE POSITION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / Actual Throttle Position.

  1. Read the value.

    Standard Value:
    Condition
    Specified Condition
    Ignition switch ON
    -5 to 5%
    Idling
    55 to 90%



NG
REPLACE DIESEL THROTTLE BODY ASSEMBLY
OK


7. INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY
  1. Inspect the electric EGR control valve assembly (Click here).



NG
REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
OK


8. READ VALUE USING INTELLIGENT TESTER (INJECTION FEEDBACK VAL #1 TO #4)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Start the engine and warm it up.

  1. Enter the following menus: Powertrain / Engine / Data List / Injection Feedback Val #1 to #4.

  1. Read the values.

    Standard Value:
    The compensatory injection volume is less than 3.0 mm3/st

    HINT:
    1. If the injector assembly is malfunctioning, the compensatory injection volume remains at 5.0 mm3/st.
    2. If there is a disconnection, the feedback value will increase and +5.0 mm3/st will be indicated, because it will become impossible for the injector assembly to inject.



NG
REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER (Click here)
OK


9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine and warm it up.

  1. Accelerate the vehicle with the accelerator depressed halfway or more starting from a speed of 120 km/h (75 mph) or more for 2 minutes (make sure the gear is fixed and does not change).

  1. Enter the following menus: Powertrain / Engine / DTC / Pending.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    No output
    A
    P0299
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)


← P0299 Turbocharger / Supercharger Underboost (Aug 2013 – Jul 2014)P0335 Crankshaft Position Sensor "A" Circuit (+ P0339) (Aug 2013 – Jul 2014) →