2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B1820/55 Short in Side Squib RH Circuit

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The side squib RH circuit consists of the center airbag sensor and front seat airbag RH.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the side squib RH circuit.
DTC Code
DTC Detection Condition
Trouble Area
B1820/55
One of the following conditions is met:
  1. The center airbag sensor detects a line short circuit signal 5 times in the side squib RH circuit during the primary check.
  2. A side squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. Floor wire
  2. Front seat airbag assembly RH (Side squib RH)
  3. Center airbag sensor assembly
B1821/55
One of the following conditions is met:
  1. The center airbag sensor detects open circuit signal in the side squib RH circuit for 2 seconds.
  2. A side squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. Floor wire
  2. Front seat airbag assembly RH (Side squib RH)
  3. Center airbag sensor assembly
B1822/55
One of the following conditions is met:
  1. The center airbag sensor detects a short circuit to ground signal in the side squib RH circuit for 0.5 seconds.
  2. A side squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. Floor wire
  2. Front seat airbag assembly RH (Side squib RH)
  3. Center airbag sensor assembly
B1823/55
One of the following conditions is met:
  1. The center airbag sensor detects a short circuit to B+ signal in the side squib RH circuit for 0.5 seconds.
  2. A side squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. Floor wire
  2. Front seat airbag assembly RH (Side squib RH)
  3. Center airbag sensor assembly

WIRING DIAGRAM

C174615E26

INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

HINT:
To perform the simulation method, enter check mode (signal check) with the intelligent tester (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here).


1. CHECK FRONT SEAT AIRBAG ASSEMBLY RH (SIDE SQUIB RH)

  1. C217719E07
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connector from the front seat airbag RH.

  1. Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the front seat airbag RH (side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1820, B1821, B1822 or B1823 is not output.

    HINT:
    Codes other than DTC B1820, B1821, B1822 and B1823 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Side Squib RH
    *2
    Center Airbag Sensor
    *3
    Connector C
    *4
    SST
    *a
    Front view of wire harness connector
    (to Side Squib RH)



NG
Go to step 2
OK

REPLACE FRONT SEAT AIRBAG ASSEMBLY RH (Click here)

2. CHECK FLOOR WIRE (SIDE SQUIB RH CIRCUIT)

  1. C216072E08
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. Disconnect the connectors from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Q7-1 (SFR+) - Body ground
    Ignition switch ON
    Below 1 V
    Q7-2 (SFR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q7-1 (SFR+) - Q7-2 (SFR-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q7-1 (SFR+) - Q7-2 (SFR-)
    Always
    1 MΩ or higher
    Q7-1 (SFR+) - Body ground
    Always
    1 MΩ or higher
    Q7-2 (SFR-) - Body ground
    Always
    1 MΩ or higher

Text in Illustration 
*1
Side Squib RH
*2
No. 2 Floor Wire
*3
Center Airbag Sensor
*4
Connector C
*a
Front view of wire harness connector
(to Side Squib RH)


NG
REPLACE FLOOR WIRE
OK


3. CHECK CENTER AIRBAG SENSOR

  1. C146261E37
    Connect the connectors to the front seat airbag RH and center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1820, B1821, B1822 or B1823 is not output.

    HINT:
    Codes other than DTC B1820, B1821, B1822 and B1823 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Side Squib RH
    *2
    Center Airbag Sensor



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1810/53 Short in Driver Side Squib 2nd Step Circuit (+ B1811/53, B1812/53, B1813/53) (from Aug 2014)B1820/55 Short in Side Squib RH Circuit (+ B1821/55, B1822/55, B1823/55) (from Aug 2014) →