2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

CAUTION:
  1. Be sure to read Precaution thoroughly before servicing (Click here).
  2. Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.
  3. If the side airbag was deployed, replace the front seat side airbag assembly, separate type front seatback spring assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.
    for Manual Seat: (Click here)
    for Power Seat: (Click here)
    for Walk in Seat Type: (Click here)

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the LH side. (for Manual Seat, Power Seat)
  5. The procedure listed below is for the RH side. (for Walk in Seat Type)


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work. (Click here)
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT SEAT HEADREST ASSEMBLY
for Manual Seat: (Click here)
for Power Seat: (Click here)
for Walk in Seat Type: (Click here)

3. REMOVE FRONT SEAT INNER TRACK BRACKET COVER LH
for Manual Seat: (Click here)
for Power Seat: (Click here)

4. REMOVE FRONT SEAT OUTER TRACK BRACKET COVER LH
for Manual Seat: (Click here)
for Power Seat: (Click here)

5. REMOVE INNER SEAT TRACK BRACKET COVER LH
for Manual Seat: (Click here)
for Power Seat: (Click here)

6. REMOVE SEAT TRACK COVER LH
for Manual Seat: (Click here)
for Power Seat: (Click here)

7. REMOVE FRONT SEAT INNER TRACK BRACKET COVER RH (for Walk in Seat Type)

B241182
  1. Operate the seat track adjusting handle to move the seat to the rearmost position.

  1. Using a moulding remover, detach the 2 claws and remove the cover.


8. REMOVE FRONT SEAT OUTER TRACK BRACKET COVER RH (for Walk in Seat Type)

B241185
  1. Using a moulding remover, detach the 2 claws.

  1. Move the cover in the direction of the arrow to detach the guide and remove the cover.


9. REMOVE INNER SEAT TRACK BRACKET COVER RH (for Walk in Seat Type)

B241188
  1. Operate the seat track adjusting handle to move the seat to the foremost position.

  1. Using a moulding remover, detach the 2 claws.

  1. Move the cover in the direction of the arrow to detach the 2 guides and remove the cover.


10. REMOVE SEAT TRACK COVER RH (for Walk in Seat Type)

B241186
  1. Using a moulding remover, detach the 2 claws.

  1. Move the cover in the direction of the arrow to detach the 2 guides and remove the cover.


11. REMOVE FRONT SEAT ASSEMBLY
for Manual Seat: (Click here)
for Power Seat: (Click here)
for Walk in Seat Type: (Click here)

12. DISCONNECT FRONT SEAT SIDE AIRBAG ASSEMBLY

  1. for Manual Seat, Power Seat:

    1. B239173
      Remove the rubber band from the seat cushion spring.

    2. B239174E01
      Detach the claw and disconnect the airbag connector.
      Text in Illustration 
      *1
      Fastening Tape

    3. Detach the 3 airbag wire harness clamps.

    4. Detach the fastening tape and open the cover.

    5. Disconnect the airbag wire harness.

  1. for Walk in Seat Type:

    1. B241196
      Remove the rubber band from the seat cushion spring.

    2. B241198E01
      Detach the claw and disconnect the airbag connector.
      Text in Illustration 
      *1
      Fastening Tape

    3. Detach the 4 airbag wire harness clamps.

    4. Detach the fastening tape and open the cover.

    5. Disconnect the airbag wire harness.


13. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD

HINT:
Use the same procedure for the RH and LH sides.

  1. B241810
    w/ Seat Heater System:
    Disconnect the seat heater connector and detach the wire harness clamp.

  1. B333273
    Remove the 3 hog rings.

  1. Open the 2 fasteners, and then open the front seatback cover.

    B242232E01

    Text in Illustration 
    *A
    for Cloth Seat
    *B
    for Leather Seat

  1. B239201
    Remove the nut and front seatback cover bracket.

  1. B239198
    Using a screwdriver, detach the 4 claws to remove the 2 front seat headrest supports.

  1. Remove the separate type seatback cover with pad.


14. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY

CAUTION:
When storing the front seat side airbag assembly, keep the airbag deployment side facing upward.

HINT:
Use the same procedure for the RH and LH sides.

  1. B251815
    Detach the 2 clamps.

  1. B333276
    Remove the 2 nuts and front seat side airbag assembly.

    CAUTION:
    1. The nuts must not be reused.
    2. Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.

← ON-VEHICLE INSPECTION (from Aug 2014)REMOVAL (from Aug 2014) →