2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B1900/73 Short in Front Pretensioner Squib RH Circuit

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The front pretensioner squib RH circuit consists of the center airbag sensor and front seat outer belt RH.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front pretensioner squib RH circuit.
DTC Code
DTC Detection Condition
Trouble Area
B1900/73
One of the following conditions is met:
  1. The center airbag sensor detects a line short circuit signal 5 times in the front pretensioner squib RH circuit during the primary check.
  2. A front pretensioner squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. Floor wire
  2. Front seat outer belt assembly RH (Front pretensioner squib RH)
  3. Center airbag sensor assembly
B1901/73
One of the following conditions is met:
  1. The center airbag sensor detects open circuit signal in the front pretensioner squib RH circuit for 2 seconds.
  2. A front pretensioner squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. Floor wire
  2. Front seat outer belt assembly RH (Front pretensioner squib RH)
  3. Center airbag sensor assembly
B1902/73
One of the following conditions is met:
  1. The center airbag sensor detects a short circuit to ground signal in the front pretensioner squib RH circuit for 0.5 seconds.
  2. A front pretensioner squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. Floor wire
  2. Front seat outer belt assembly RH (Front pretensioner squib RH)
  3. Center airbag sensor assembly
B1903/73
One of the following conditions is met:
  1. The center airbag sensor detects a short circuit to B+ signal in the front pretensioner squib RH circuit for 0.5 seconds.
  2. A front pretensioner squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. Floor wire
  2. Front seat outer belt assembly RH (Front pretensioner squib RH)
  3. Center airbag sensor assembly

WIRING DIAGRAM

C174615E44

INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

HINT:
To perform the simulation method, enter check mode (signal check) with the intelligent tester (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here).


1. CHECK FRONT SEAT OUTER BELT RH (FRONT PRETENSIONER SQUIB RH)

  1. C213955E02
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the front seat outer belt RH.

  1. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the front seat outer belt RH (front pretensioner squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1900, B1901, B1902 or B1903 is not output.

    HINT:
    Codes other than DTC B1900, B1901, B1902 and B1903 may be output at this time, but they are not related to this check.

    Result 
    Result
    Proceed to
    OK (for 3 Door)
    A
    OK (for 5 Door)
    B
    NG
    C
    Text in Illustration 
    *1
    Front Pretensioner Squib RH
    *2
    Center Airbag Sensor
    *3
    Connector C
    *4
    SST
    *a
    Front view of wire harness connector
    (to Front Pretensioner Squib RH)



A
REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH (Click here)

B
REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH (Click here)
C


2. CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. C214775E01
    Check that the floor wire connector (on the front seat outer belt RH side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

    Text in Illustration 
    *1
    Front Pretensioner Squib RH
    *2
    Center Airbag Sensor



NG
REPLACE FLOOR WIRE
OK


3. CHECK FLOOR WIRE (FRONT PRETENSIONER SQUIB RH CIRCUIT)

  1. C213956E02
    Disconnect the connectors from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Q2-1 (R+) - Body ground
    Ignition switch ON
    Below 1 V
    Q2-2 (R-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q2-1 (R+) - Q2-2 (R-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q2-1 (R+) - Q2-2 (R-)
    Always
    1 MΩ or higher
    Q2-1 (R+) - Body ground
    Always
    1 MΩ or higher
    Q2-2 (R-) - Body ground
    Always
    1 MΩ or higher

Text in Illustration 
*1
Front Pretensioner Squib RH
*2
Floor Wire
*3
Center Airbag Sensor
*4
Connector C
*a
Front view of wire harness connector
(to Front Pretensioner Squib RH)


NG
REPLACE FLOOR WIRE
OK


4. CHECK CENTER AIRBAG SENSOR

  1. C146261E37
    Connect the connectors to the front seat outer belt RH and center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1900, B1901, B1902 or B1903 is not output.

    HINT:
    Codes other than DTC B1900, B1901, B1902 and B1903 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Pretensioner Squib RH
    *2
    Center Airbag Sensor



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1900/73 Short in Front Pretensioner Squib RH Circuit (+ B1901/73, B1902/73, B1903/73) (Aug 2013 – Jul 2014)B1900/73 Short in Front Driver Side Pretensioner Squib Circuit (+ B1901/73, B1902/73, B1903/73) (Aug 2013 – Jul 2014) →