2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

INSPECTION

Inspection · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


INSPECT SPIRAL CABLE SUB-ASSEMBLY (w/o Steering Heater)
  1. If any of the defects mentioned below are found, replace the spiral cable sub-assembly with a new one:
    Scratches, cracks, dents or chips on the connector or the spiral cable sub-assembly.

  1. B362419E01
    Check the spiral cable sub-assembly.
    Text in Illustration 
    *a
    Component without harness connected
    (Spiral Cable Sub-assembly)
    *b
    Orange
    *c
    Black

    1. Set the spiral cable sub-assembly to the center position (Click here).

    2. After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise and measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      G41-1 - z5-2
      Always
      Below 1 Ω
      G41-2 - z5-1
      Always
      Below 1 Ω
      G41-3 - z6-1
      Always
      Below 1 Ω
      G41-4 - z6-2
      Always
      Below 1 Ω
      G40-6 - z8-10
      Always
      3 Ω or less
      G40-5 - z8-9
      Always
      3 Ω or less
      G40-4 - z8-8
      Always
      3 Ω or less
      G40-3 - z8-7
      Always
      3 Ω or less
      G40-2 - z8-6
      Always
      3 Ω or less
      G40-2 - z7-4
      Always
      3 Ω or less
      G40-1 - z7-3
      Always
      3 Ω or less
      G40-12 - z8-5
      Always
      3 Ω or less
      G40-11 - z8-4
      Always
      3 Ω or less
      G40-10 - z8-3
      Always
      3 Ω or less
      G40-9 - z8-2
      Always
      3 Ω or less
      G40-8 - z8-1
      Always
      3 Ω or less
      G40-8 - z7-2
      Always
      3 Ω or less
      G40-7 - z7-1
      Always
      3 Ω or less

    3. After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times counterclockwise. Then while rotating the spiral cable sub-assembly 5 times clockwise, measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      G41-1 - z5-2
      Always
      Below 1 Ω
      G41-2 - z5-1
      Always
      Below 1 Ω
      G41-3 - z6-1
      Always
      Below 1 Ω
      G41-4 - z6-2
      Always
      Below 1 Ω
      G40-6 - z8-10
      Always
      3 Ω or less
      G40-5 - z8-9
      Always
      3 Ω or less
      G40-4 - z8-8
      Always
      3 Ω or less
      G40-3 - z8-7
      Always
      3 Ω or less
      G40-2 - z8-6
      Always
      3 Ω or less
      G40-2 - z7-4
      Always
      3 Ω or less
      G40-1 - z7-3
      Always
      3 Ω or less
      G40-12 - z8-5
      Always
      3 Ω or less
      G40-11 - z8-4
      Always
      3 Ω or less
      G40-10 - z8-3
      Always
      3 Ω or less
      G40-9 - z8-2
      Always
      3 Ω or less
      G40-8 - z8-1
      Always
      3 Ω or less
      G40-8 - z7-2
      Always
      3 Ω or less
      G40-7 - z7-1
      Always
      3 Ω or less

      NOTICE:
      As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.

      If the result is not as specified, replace the spiral cable sub-assembly.


INSPECT SPIRAL CABLE SUB-ASSEMBLY (w/ Steering Heater)
  1. If any of the defects mentioned below are found, replace the spiral cable sub-assembly with a new one:
    Scratches, cracks, dents or chips on the connector or the spiral cable sub-assembly.

  1. E284655E01
    Check the spiral cable sub-assembly.
    Text in Illustration 
    *a
    Component without harness connected
    (Spiral Cable Sub-assembly)
    *b
    Orange
    *c
    Black

    1. Set the spiral cable sub-assembly to the center position (Click here).

    2. After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise and measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      G41-1 - z5-2
      Always
      Below 1 Ω
      G41-2 - z5-1
      Always
      Below 1 Ω
      G41-3 - z6-1
      Always
      Below 1 Ω
      G41-4 - z6-2
      Always
      Below 1 Ω
      G40-6 - z8-10
      Always
      3 Ω or less
      G40-5 - z8-9
      Always
      3 Ω or less
      G40-4 - z8-8
      Always
      3 Ω or less
      G40-3 - z8-7
      Always
      3 Ω or less
      G40-2 - z8-6
      Always
      3 Ω or less
      G40-2 - z7-4
      Always
      3 Ω or less
      G40-1 - z7-3
      Always
      3 Ω or less
      G40-12 - z8-5
      Always
      3 Ω or less
      G40-11 - z8-4
      Always
      3 Ω or less
      G40-10 - z8-3
      Always
      3 Ω or less
      G40-9 - z8-2
      Always
      3 Ω or less
      G40-8 - z8-1
      Always
      3 Ω or less
      G40-8 - z7-2
      Always
      3 Ω or less
      G40-7 - z7-1
      Always
      3 Ω or less
      z14-1 - G151-1
      Always
      Below 0.1 Ω
      z14-2 - G151-3
      Always
      Below 0.1 Ω
      z14-3 - G151-2
      Always
      Below 0.1 Ω
      z14-4 - G151-4
      Always
      Below 0.1 Ω

    3. After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times counterclockwise. Then while rotating the spiral cable sub-assembly 5 times clockwise, measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      G41-1 - z5-2
      Always
      Below 1 Ω
      G41-2 - z5-1
      Always
      Below 1 Ω
      G41-3 - z6-1
      Always
      Below 1 Ω
      G41-4 - z6-2
      Always
      Below 1 Ω
      G40-6 - z8-10
      Always
      3 Ω or less
      G40-5 - z8-9
      Always
      3 Ω or less
      G40-4 - z8-8
      Always
      3 Ω or less
      G40-3 - z8-7
      Always
      3 Ω or less
      G40-2 - z8-6
      Always
      3 Ω or less
      G40-2 - z7-4
      Always
      3 Ω or less
      G40-1 - z7-3
      Always
      3 Ω or less
      G40-12 - z8-5
      Always
      3 Ω or less
      G40-11 - z8-4
      Always
      3 Ω or less
      G40-10 - z8-3
      Always
      3 Ω or less
      G40-9 - z8-2
      Always
      3 Ω or less
      G40-8 - z8-1
      Always
      3 Ω or less
      G40-8 - z7-2
      Always
      3 Ω or less
      G40-7 - z7-1
      Always
      3 Ω or less
      z14-1 - G151-1
      Always
      Below 0.1 Ω
      z14-2 - G151-3
      Always
      Below 0.1 Ω
      z14-3 - G151-2
      Always
      Below 0.1 Ω
      z14-4 - G151-4
      Always
      Below 0.1 Ω

      NOTICE:
      As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.

      If the result is not as specified, replace the spiral cable sub-assembly.

← REMOVAL (from Aug 2014)INSPECTION (from Aug 2014) →