INSPECTION
Inspection · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
| INSPECT SPIRAL CABLE SUB-ASSEMBLY (w/o Steering Heater) |
If any of the defects mentioned below are found, replace the spiral cable sub-assembly with a new one:
Scratches, cracks, dents or chips on the connector or the spiral cable sub-assembly.
Check the spiral cable sub-assembly.

Text in Illustration *a
Component without harness connected
(Spiral Cable Sub-assembly)
*b
Orange
*c
Black
Set the spiral cable sub-assembly to the center position (Click here).
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise and measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G41-1 - z5-2
Always
Below 1 Ω
G41-2 - z5-1
Always
Below 1 Ω
G41-3 - z6-1
Always
Below 1 Ω
G41-4 - z6-2
Always
Below 1 Ω
G40-6 - z8-10
Always
3 Ω or less
G40-5 - z8-9
Always
3 Ω or less
G40-4 - z8-8
Always
3 Ω or less
G40-3 - z8-7
Always
3 Ω or less
G40-2 - z8-6
Always
3 Ω or less
G40-2 - z7-4
Always
3 Ω or less
G40-1 - z7-3
Always
3 Ω or less
G40-12 - z8-5
Always
3 Ω or less
G40-11 - z8-4
Always
3 Ω or less
G40-10 - z8-3
Always
3 Ω or less
G40-9 - z8-2
Always
3 Ω or less
G40-8 - z8-1
Always
3 Ω or less
G40-8 - z7-2
Always
3 Ω or less
G40-7 - z7-1
Always
3 Ω or less
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times counterclockwise. Then while rotating the spiral cable sub-assembly 5 times clockwise, measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G41-1 - z5-2
Always
Below 1 Ω
G41-2 - z5-1
Always
Below 1 Ω
G41-3 - z6-1
Always
Below 1 Ω
G41-4 - z6-2
Always
Below 1 Ω
G40-6 - z8-10
Always
3 Ω or less
G40-5 - z8-9
Always
3 Ω or less
G40-4 - z8-8
Always
3 Ω or less
G40-3 - z8-7
Always
3 Ω or less
G40-2 - z8-6
Always
3 Ω or less
G40-2 - z7-4
Always
3 Ω or less
G40-1 - z7-3
Always
3 Ω or less
G40-12 - z8-5
Always
3 Ω or less
G40-11 - z8-4
Always
3 Ω or less
G40-10 - z8-3
Always
3 Ω or less
G40-9 - z8-2
Always
3 Ω or less
G40-8 - z8-1
Always
3 Ω or less
G40-8 - z7-2
Always
3 Ω or less
G40-7 - z7-1
Always
3 Ω or less
- NOTICE:
- As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.
| INSPECT SPIRAL CABLE SUB-ASSEMBLY (w/ Steering Heater) |
If any of the defects mentioned below are found, replace the spiral cable sub-assembly with a new one:
Scratches, cracks, dents or chips on the connector or the spiral cable sub-assembly.
Check the spiral cable sub-assembly.

Text in Illustration *a
Component without harness connected
(Spiral Cable Sub-assembly)
*b
Orange
*c
Black
Set the spiral cable sub-assembly to the center position (Click here).
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise and measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G41-1 - z5-2
Always
Below 1 Ω
G41-2 - z5-1
Always
Below 1 Ω
G41-3 - z6-1
Always
Below 1 Ω
G41-4 - z6-2
Always
Below 1 Ω
G40-6 - z8-10
Always
3 Ω or less
G40-5 - z8-9
Always
3 Ω or less
G40-4 - z8-8
Always
3 Ω or less
G40-3 - z8-7
Always
3 Ω or less
G40-2 - z8-6
Always
3 Ω or less
G40-2 - z7-4
Always
3 Ω or less
G40-1 - z7-3
Always
3 Ω or less
G40-12 - z8-5
Always
3 Ω or less
G40-11 - z8-4
Always
3 Ω or less
G40-10 - z8-3
Always
3 Ω or less
G40-9 - z8-2
Always
3 Ω or less
G40-8 - z8-1
Always
3 Ω or less
G40-8 - z7-2
Always
3 Ω or less
G40-7 - z7-1
Always
3 Ω or less
z14-1 - G151-1
Always
Below 0.1 Ω
z14-2 - G151-3
Always
Below 0.1 Ω
z14-3 - G151-2
Always
Below 0.1 Ω
z14-4 - G151-4
Always
Below 0.1 Ω
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times counterclockwise. Then while rotating the spiral cable sub-assembly 5 times clockwise, measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G41-1 - z5-2
Always
Below 1 Ω
G41-2 - z5-1
Always
Below 1 Ω
G41-3 - z6-1
Always
Below 1 Ω
G41-4 - z6-2
Always
Below 1 Ω
G40-6 - z8-10
Always
3 Ω or less
G40-5 - z8-9
Always
3 Ω or less
G40-4 - z8-8
Always
3 Ω or less
G40-3 - z8-7
Always
3 Ω or less
G40-2 - z8-6
Always
3 Ω or less
G40-2 - z7-4
Always
3 Ω or less
G40-1 - z7-3
Always
3 Ω or less
G40-12 - z8-5
Always
3 Ω or less
G40-11 - z8-4
Always
3 Ω or less
G40-10 - z8-3
Always
3 Ω or less
G40-9 - z8-2
Always
3 Ω or less
G40-8 - z8-1
Always
3 Ω or less
G40-8 - z7-2
Always
3 Ω or less
G40-7 - z7-1
Always
3 Ω or less
z14-1 - G151-1
Always
Below 0.1 Ω
z14-2 - G151-3
Always
Below 0.1 Ω
z14-3 - G151-2
Always
Below 0.1 Ω
z14-4 - G151-4
Always
Below 0.1 Ω
- NOTICE:
- As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.
