2013-2015 Land Cruiser Prado · Service Manual Suspension

C1715/15 Front Acceleration Sensor RH Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The acceleration sensor (up and down G sensor) detects the upward and downward acceleration of the vehicle, and outputs it as a voltage to the suspension control ECU. Up and down G sensors are installed in 3 locations: 1) the suspension control ECU, 2) the RH side instrument panel, and 3) behind the deck trim side panel assembly LH. Each up and down G sensor independently detects the upward and downward acceleration. During a test mode inspection, the suspension control ECU reads the fluctuations in each sensor signal. If a sensor signal does not fluctuate, test mode DTCs C1796/96, C1797/97 and C1798/98 are stored.
DTC Code
DTC Detection Condition
Trouble Area
C1715/15
Either condition is met:
  1. With the ignition switch ON, a voltage of 5.5 V or higher or 4.3 V or less at the power source of the front acceleration sensor RH is detected for 0.5 seconds.
  2. With the ignition switch ON, a voltage of 4.7 V or higher or 0.3 V or less at the front acceleration sensor RH is detected for 1 second.
  1. Harness or connector
  2. Front acceleration sensor RH
  3. Suspension control ECU
C1716/16
Either condition is met:
  1. With the ignition switch ON, a voltage of 5.5 V or higher or 4.3 V or less at the power source of the front acceleration sensor LH is detected for 0.5 seconds.
  2. With the ignition switch ON, a voltage of 4.7 V or higher or 0.3 V or less at the front acceleration sensor LH is detected for 1 second.
Suspension control ECU (Front acceleration sensor LH)
C1717/17
Either condition is met:
  1. With the ignition switch ON, a voltage of 5.5 V or higher or 4.3 V or less at the power source of the rear acceleration sensor is detected for 0.5 seconds.
  2. With the ignition switch ON, a voltage of 4.7 V or higher or 0.3 V or less at the rear acceleration sensor is detected for 1 second.
  1. Harness or connector
  2. Rear acceleration sensor
  3. Suspension control ECU
C1796/96
On a level surface, the G sensor input is +/- 1.96 m/s2 or more for 1 second or more.
  1. Harness or connector
  2. Front acceleration sensor RH
  3. Suspension control ECU
C1797/97
On a level surface, the G sensor input is +/- 1.96 m/s2 or more for 1 second or more.
Suspension control ECU (Front acceleration sensor LH)
C1798/98
On a level surface, the G sensor input is +/- 1.96 m/s2 or more for 1 second or more.
  1. Harness or connector
  2. Rear acceleration sensor
  3. Suspension control ECU

HINT:
If DTCs C1716/16 and C1797/97 are output, replace the suspension control ECU (houses the front acceleration sensor LH).


WIRING DIAGRAM

C179515E05

INSPECTION PROCEDURE

NOTICE:
When replacing the suspension control ECU, perform registration (Click here).


1. READ VALUE USING INTELLIGENT TESTER (G SENSOR)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / Air suspension / Data List.

    Air Suspension 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    (Up & Down) G Sensor FR
    (Up & Down) G sensor (Front RH)/
    Min.: -1045.29 m/s2
    Max.: 1045.26 m/s2
    0 +/- 0.98 m/s2 when stationary
    The value changes when the vehicle (Front RH) is bounced.
    (Up & Down) G Sensor FL
    (Up & Down) G sensor (Front LH)/
    Min.: -1045.29 m/s2
    Max.: 1045.26 m/s2
    0 +/- 0.98 m/s2 when stationary
    The value changes when the vehicle (Front LH) is bounced.
    (Up & Down) G Sensor Rear
    (Up & Down) G sensor (Rear)/
    Min.: -1045.29 m/s2
    Max.: 1045.26 m/s2
    0 +/- 0.98 m/s2 when stationary
    The value changes when the vehicle (rear) is bounced.

    OK:
    Acceleration value changes.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. INSPECT ACCELERATION SENSOR (FRONT RH OR REAR)
C214175E04
Text in Illustration 
*A
for Front RH
*B
for Rear
*a
Component without harness connected
(Acceleration Sensor)
V100135
Upside
V100136
Downside
  1. Check the front acceleration sensor RH (when DTC C1715/15 or C1796/96 is output).

    1. Remove the front acceleration sensor RH (Click here).

    2. Connect 3 dry cell batteries of 1.5 V in series.

    3. Connect the positive (+) end of the batteries to terminal 3 (SHB) of the acceleration sensor and the negative (-) end of the batteries to terminal 2 (SHG). Then measure the voltage between terminal 1 (SGFL) and terminal 2 (SHG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      1 (SGFL) - 2 (SHG)
      Sensor in vertical position
      Approx. 2.0 to 2.5 V
      Sensor tilted left or right from vertical position
      Changes between approx. 0.9 and 2.3 V

  1. Check the rear acceleration sensor: (when DTC C1717/17 or C1798/98 is output).

    1. Remove the rear acceleration sensor (Click here).

    2. Connect 3 dry cell batteries of 1.5 V in series.

    3. Connect the positive (+) end of the batteries to terminal 3 (SGV) of the acceleration sensor and the negative (-) end of the batteries to terminal 2 (SGND). Then measure the voltage between terminal 1 (SGRR) and terminal 2 (SGND).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      1 (SGRR) - 2 (SGND)
      Sensor in vertical position
      Approx. 2.0 to 2.5 V
      Sensor tilted left or right from vertical position
      Changes between approx. 0.9 and 2.3 V

      NOTICE:
      Do not apply a voltage of higher than 6 V.

      HINT:
      When the acceleration sensor is tilted, it may output a different value.

      Result 
      Result
      Proceed to
      OK
      A
      NG (Front acceleration sensor RH)
      B
      NG (Rear acceleration sensor)
      C



B
REPLACE FRONT ACCELERATION SENSOR RH (Click here)

C
REPLACE REAR ACCELERATION SENSOR (Click here)
A


3. CHECK HARNESS AND CONNECTOR (ACCELERATION SENSOR - SUSPENSION CONTROL ECU)
  1. Check the front acceleration sensor RH (when DTC C1715/15 or C1796/96 is output).

    1. Disconnect the A13 front acceleration sensor RH connector.

    2. Disconnect the A14 suspension control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A13-1 (SGFL) - A14-18 (SGFR)
      Always
      Below 1 Ω
      A13-2 (SHG) - A14-10 (SGR)
      Always
      Below 1 Ω
      A13-3 (SHB) - A14-9 (SBR)
      Always
      Below 1 Ω
      A13-1 (SGFL) - Body ground
      Always
      10 kΩ or higher
      A13-2 (SHG) - Body ground
      Always
      10 kΩ or higher
      A13-3 (SHB) - Body ground
      Always
      10 kΩ or higher

  1. Check the rear acceleration sensor: (when DTC C1717/17 or C1798/98 is output).

    1. Disconnect the R18 rear acceleration sensor connector.

    2. Disconnect the A49 suspension control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      R18-1 (SGRR) - A49-26 (SGRR)
      Always
      Below 1 Ω
      R18-2 (SGND) - A49-16 (SGR3)
      Always
      Below 1 Ω
      R18-3 (SGV) - A49-17 (SBR3)
      Always
      Below 1 Ω
      R18-1 (SGRR) - Body ground
      Always
      10 kΩ or higher
      R18-2 (SGND) - Body ground
      Always
      10 kΩ or higher
      R18-3 (SGV) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SUSPENSION CONTROL ECU (Click here)


← C1715/15 Front Acceleration Sensor RH Malfunction (+ 5 more codes) (Aug 2013 – Jul 2014)C1731/31 FR Damping Force Control Actuator Circuit (+ C1732/32, C1733/33, C1734/34) (Aug 2013 – Jul 2014) →