C1715/15 Front Acceleration Sensor RH Malfunction
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Also covers:
- C1716/16 Front Acceleration Sensor LH Malfunction
- C1717/17 Rear Acceleration Sensor Malfunction
- C1796/96 (Up & Down) G Sensor FR
- C1797/97 (Up & Down) G Sensor FL
- C1798/98 (Up & Down) G Sensor Rear
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The acceleration sensor (up and down G sensor) detects the upward and downward acceleration of the vehicle, and outputs it as a voltage to the suspension control ECU. Up and down G sensors are installed in 3 locations: 1) the suspension control ECU, 2) the RH side instrument panel, and 3) behind the deck trim side panel assembly LH. Each up and down G sensor independently detects the upward and downward acceleration. During a test mode inspection, the suspension control ECU reads the fluctuations in each sensor signal. If a sensor signal does not fluctuate, test mode DTCs C1796/96, C1797/97 and C1798/98 are stored.| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1715/15 |
Either condition is met:
|
|
| C1716/16 |
Either condition is met:
|
Suspension control ECU (Front acceleration sensor LH) |
| C1717/17 |
Either condition is met:
|
|
| C1796/96 |
On a level surface, the G sensor input is +/- 1.96 m/s2 or more for 1 second or more. |
|
| C1797/97 |
On a level surface, the G sensor input is +/- 1.96 m/s2 or more for 1 second or more. |
Suspension control ECU (Front acceleration sensor LH) |
| C1798/98 |
On a level surface, the G sensor input is +/- 1.96 m/s2 or more for 1 second or more. |
|
- HINT:
- If DTCs C1716/16 and C1797/97 are output, replace the suspension control ECU (houses the front acceleration sensor LH).
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the suspension control ECU, perform registration (Click here).
| 1. READ VALUE USING INTELLIGENT TESTER (G SENSOR) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / Air suspension / Data List.
Air Suspension Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
(Up & Down) G Sensor FR
(Up & Down) G sensor (Front RH)/
Min.: -1045.29 m/s2
Max.: 1045.26 m/s2
0 +/- 0.98 m/s2 when stationary
The value changes when the vehicle (Front RH) is bounced.
(Up & Down) G Sensor FL
(Up & Down) G sensor (Front LH)/
Min.: -1045.29 m/s2
Max.: 1045.26 m/s2
0 +/- 0.98 m/s2 when stationary
The value changes when the vehicle (Front LH) is bounced.
(Up & Down) G Sensor Rear
(Up & Down) G sensor (Rear)/
Min.: -1045.29 m/s2
Max.: 1045.26 m/s2
0 +/- 0.98 m/s2 when stationary
The value changes when the vehicle (rear) is bounced.
- OK:
- Acceleration value changes.
|
|
||||
| OK | ||
| ||
| 2. INSPECT ACCELERATION SENSOR (FRONT RH OR REAR) |
![]() ![]() |
| *A |
for Front RH |
| *B |
for Rear |
| *a |
Component without harness connected (Acceleration Sensor) |
![]() ![]() |
Upside |
![]() ![]() |
Downside |
Check the front acceleration sensor RH (when DTC C1715/15 or C1796/96 is output).
Remove the front acceleration sensor RH (Click here).
Connect 3 dry cell batteries of 1.5 V in series.
Connect the positive (+) end of the batteries to terminal 3 (SHB) of the acceleration sensor and the negative (-) end of the batteries to terminal 2 (SHG). Then measure the voltage between terminal 1 (SGFL) and terminal 2 (SHG).
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
1 (SGFL) - 2 (SHG)
Sensor in vertical position
Approx. 2.0 to 2.5 V
Sensor tilted left or right from vertical position
Changes between approx. 0.9 and 2.3 V
Check the rear acceleration sensor: (when DTC C1717/17 or C1798/98 is output).
Remove the rear acceleration sensor (Click here).
Connect 3 dry cell batteries of 1.5 V in series.
Connect the positive (+) end of the batteries to terminal 3 (SGV) of the acceleration sensor and the negative (-) end of the batteries to terminal 2 (SGND). Then measure the voltage between terminal 1 (SGRR) and terminal 2 (SGND).
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
1 (SGRR) - 2 (SGND)
Sensor in vertical position
Approx. 2.0 to 2.5 V
Sensor tilted left or right from vertical position
Changes between approx. 0.9 and 2.3 V
- NOTICE:
- Do not apply a voltage of higher than 6 V.
- HINT:
- When the acceleration sensor is tilted, it may output a different value.
Result Result
Proceed to
OK
A
NG (Front acceleration sensor RH)
B
NG (Rear acceleration sensor)
C
|
|
||||
|
|
||||
| A | |
| 3. CHECK HARNESS AND CONNECTOR (ACCELERATION SENSOR - SUSPENSION CONTROL ECU) |
Check the front acceleration sensor RH (when DTC C1715/15 or C1796/96 is output).
Disconnect the A13 front acceleration sensor RH connector.
Disconnect the A14 suspension control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A13-1 (SGFL) - A14-18 (SGFR)
Always
Below 1 Ω
A13-2 (SHG) - A14-10 (SGR)
Always
Below 1 Ω
A13-3 (SHB) - A14-9 (SBR)
Always
Below 1 Ω
A13-1 (SGFL) - Body ground
Always
10 kΩ or higher
A13-2 (SHG) - Body ground
Always
10 kΩ or higher
A13-3 (SHB) - Body ground
Always
10 kΩ or higher
Check the rear acceleration sensor: (when DTC C1717/17 or C1798/98 is output).
Disconnect the R18 rear acceleration sensor connector.
Disconnect the A49 suspension control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
R18-1 (SGRR) - A49-26 (SGRR)
Always
Below 1 Ω
R18-2 (SGND) - A49-16 (SGR3)
Always
Below 1 Ω
R18-3 (SGV) - A49-17 (SBR3)
Always
Below 1 Ω
R18-1 (SGRR) - Body ground
Always
10 kΩ or higher
R18-2 (SGND) - Body ground
Always
10 kΩ or higher
R18-3 (SGV) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||



