B1446/46 Air Mix Damper Control Servo Motor Circuit (Driver Side)
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The damper servo sub-assembly (driver side air mix damper servo) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air mix damper (for driver side) to any position. As a result, the air mix damper (for driver side) varies the mixture of hot air from the heater core and cold air from the evaporator so that the temperature of the air blowing toward the front passenger side is as requested.- HINT:
- Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B1446/46 |
The air mix damper position does not change when the air conditioning amplifier assembly operates the damper servo sub-assembly (driver side air mix damper servo). |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
DTC B1446/46 is not output
A
DTC B1446/46 is output
B
DTC B1446/46 and B1497/97 are output
C
|
|
||||
|
|
||||
| A | ||
| ||
| 2. READ VALUE USING INTELLIGENT TESTER (DRIVER SIDE AIR MIX DAMPER SERVO) |
Use the Data List to check if the damper servo sub-assembly (driver side air mix damper servo) is functioning properly (Click here).
Air Conditioner Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Air Mix Servo Targ Pulse (D)
Damper servo sub-assembly (driver side air mix damper servo) target pulse / Min.: 0, Max.: 255
for LHD: - 107 (pulse): MAX COOL
- 26 (pulse): MAX HOT
- 112 or 127 (pulse): MAX COOL
- 21 or 31 (pulse): MAX HOT
-
Air Mix Servo Actual Pulse (D)
Damper servo sub-assembly (driver side air mix damper servo) actual pulse / Min.: 0, Max.: 255
for LHD: - 107 (pulse): MAX COOL
- 26 (pulse): MAX HOT
- 112 or 127 (pulse): MAX COOL
- 21 or 31 (pulse): MAX HOT
-
- OK:
- The display is as specified in the normal condition column.
Result Result
Proceed to
OK (When troubleshooting according to the DTC)
A
OK (When troubleshooting according to Problem Symptoms Table
B
Both target pulse and actual pulse do not display
C
Target pulse displays normally, but actual pulse does not display
D
- 107 (pulse): MAX COOL
|
|
||||
|
|
||||
|
|
||||
| A | |
| 3. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC B1446 is not output.
|
|
||||
| OK | ||
| ||
| 4. CHECK DAMPER SERVO SUB-ASSEMBLY (DRIVER SIDE AIR MIX DAMPER SERVO) |
Replace the damper servo sub-assembly (driver side air mix damper servo) (Click here).
- HINT:
- Since the damper servo sub-assembly (driver side air mix damper servo) cannot be inspected while it is removed from the vehicle, replace the damper servo sub-assembly (driver side air mix damper servo) with a new or normally functioning one.
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC B1446 is not output.
|
|
||||
| OK | ||
| ||
| 5. CHECK AIR CONDITIONING HARNESS ASSEMBLY |
Temporarily replace the air conditioning harness assembly with a new or normally functioning one (Click here).
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC B1446 is not output.
|
|
||||
| OK | ||
| ||
