B2762 Intrusion Sensor Signal Circuit Malfunction
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Also covers:
- B2764 Short to GND in Intrusion Sensor Signal Circuit
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The theft warning radar sensor (intrusion sensor) conducts a self-diagnosis immediately after power is supplied to the sensor (when the theft deterrent system is set).If a malfunction is detected in the IOUT line, the main body ECU stores DTC B2762.
DTC B2764 is stored when terminal IOUT of the theft warning radar sensor (intrusion sensor) has not received a signal for 5 seconds or more.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2762 |
After a normal/trouble signal is output from the theft warning radar sensor (intrusion sensor) as a result of self-diagnosis, either of the following malfunctions is detected:
|
|
| B2764 |
After a normal/trouble signal is output from the theft warning radar sensor (intrusion sensor) as a result of self-diagnosis, the following malfunction is detected: Terminal IOUT of the theft warning radar sensor (intrusion sensor) has not received a signal for 5 seconds or more. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. CHECK HARNESS AND CONNECTOR (MAP LIGHT - BATTERY AND BODY GROUND) |
Disconnect the W7 light connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
W7-5 (GND3) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
W7-7 (S+B) - Body ground
Always
11 to 14 V
| *a |
Front view of wire harness connector (to Map Light Assembly) |
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (MAP LIGHT - MAIN BODY ECU) |
Disconnect the W7 light connector.
Disconnect the G63 ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
W7-6 (IOUT) - G63-12 (ISIF)
Always
Below 1 Ω
W7-6 (IOUT) or G63-12 (ISIF) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 3. CHECK MAP LIGHT ASSEMBLY (THEFT WARNING RADAR SENSOR) |
Using an oscilloscope, check the waveform.

Measurement Condition Item
Content
Tester Connection
W7-6 (IOUT) - Body ground
Tool Setting
2 V/DIV., 100 ms./DIV.
Condition
Immediately after theft deterrent system set
- HINT:
- If the intrusion sensor is normal when the map light receives a HI input signal from the main body ECU, the sensor outputs the initial response.
- When the input signal from the main body ECU is LOW and does not change, the main body ECU may be malfunctioning.
- If the intrusion sensor is normal when the map light receives a HI input signal from the main body ECU, the sensor outputs the initial response.
- OK:
- Initial response occurs (refer to illustration).
Text in Illustration *a
Component with harness connected
(Map Light Assembly)
*b
Waveform
*c
Initial Response
Result Result
Proceed to
OK
A
NG (Signal is LOW and does not change)
B
NG (Signal is HIGH and does not change)
C
|
|
||||
|
|
||||
| A | ||
| ||
