2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B1500 Fuel Sender Open Detected

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

This DTC is stored when the combination meter detects a fuel sender gauge malfunction.
DTC Code
DTC Detection Condition
Trouble Area
B1500
When the combination meter detects a fuel sender gauge malfunction.
  1. Harness or connector
  2. Combination meter assembly
  3. Fuel suction with pump and gauge tube assembly
  4. Fuel tank vent tube assembly
  5. Fuel sender gauge assembly

WIRING DIAGRAM

E202183E02
E204093E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (FUEL SENDER GAUGE)
  1. Operate the intelligent tester according to the display and select the Data List (Click here).

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Fuel Input
    Fuel sender gauge (main) input signal/Min.: 0, Max.: 127.5
    Fuel sender input value
    Unit: L

    OK:
    Fuel amount value displayed on the intelligent tester is almost the same as needle indication.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (COMBINATION METER - FUEL SENDER GAUGE AND BODY GROUND)
  1. Disconnect the G6 meter connector.

  1. Disconnect the S5 gauge connector.

  1. Disconnect the R40 gauge connector*.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G6-9 (L) - S5-2 (FS)
    Always
    Below 1 Ω
    G6-24 (E) - S5-3 (FE)
    G6-9 (L) - R40-3*
    G6-24 (E) - R40-1*
    G6-21 (E2) - Body ground

  1. *: for 3 Door


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK ENGINE TYPE
  1. Check the engine type.

    Engine Type 
    Engine type
    Proceed to
    for 1GR-FE
    A
    for 2TR-FE
    B
    for 1KD-FTV
    C
    for 5L-E
    D



B
Go to step 6

C
Go to step 8

D
Go to step 13
A


4. INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (for 1GR-FE)

  1. E158805E06
    Remove the fuel sender gauge.
    1. for 1GR-FE, Single Tank Type: (Click here)
    2. for 1GR-FE, Double Tank Type: (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 (FS) - B-2
    Always
    Below 1 Ω
    A-3 (FE) - B-1

    Text in Illustration 
    *a
    Component without harness connected (Fuel Suction With Pump and Gauge Tube Assembly)
    *b
    Lower side (to Fuel Sender Gauge Assembly)
    *c
    Connector A
    *d
    Connector B
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Single Tank Type)
    B
    NG (for Double Tank Type)
    C



B
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)

C
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)
A


5. INSPECT FUEL SENDER GAUGE ASSEMBLY (for 1GR-FE)

  1. E201786E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F
    12 to 18 Ω
    Float level is E
    405 to 415 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector (to Fuel Sender Gauge Assembly)
    *b
    Float Level F (Upper)
    *c
    Float Level E (Lower)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Single Tank Type)
    B
    NG (for Double Tank Type)
    C



B
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

C
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)

6. INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (for 2TR-FE)
E158805E06

NOTICE:
For 3 door vehicles, proceed to next step.

  1. Remove the fuel sender gauge.

    1. for 2TR-FE, Single Tank Type: (Click here)
    2. for 2TR-FE, Double Tank Type: (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 (FS) - B-2
    Always
    Below 1 Ω
    A-3 (FE) - B-1

    Text in Illustration 
    *a
    Component without harness connected (Fuel Suction With Pump and Gauge Tube Assembly)
    *b
    Lower side (to Fuel Sender Gauge Assembly)
    *c
    Connector A
    *d
    Connector B
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Single Tank Type)
    B
    NG (for Double Tank Type)
    C



B
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)

C
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)
A


7. INSPECT FUEL SENDER GAUGE ASSEMBLY (for 2TR-FE)
for 3 Door:
  1. Remove the fuel sender gauge (Click here).

  1. A223162E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Float level is F
    12 to 18 Ω
    Float level is E
    405 to 415 Ω

    Text in Illustration 
    *a
    Component without harness connected (Fuel Sender Gauge Assembly)
    *b
    Float Level F (Upper)
    *c
    Float Level E (Lower)

for 5 Door:

  1. E201786E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F
    12 to 18 Ω
    Float level is E
    405 to 415 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector (Fuel Sender Gauge Assembly)
    *b
    Float Level F (Upper)
    *c
    Float Level E (Lower)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Single Tank Type)
    B
    NG (for Double Tank Type)
    C



B
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

C
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)

8. CHECK FUEL TANK TYPE
  1. Check the fuel tank type.

    Fuel Tank Type 
    Fuel Tank Type
    Proceed to
    Single tank type
    A
    Double tank type
    B



B
Go to step 11
A


9. INSPECT FUEL TANK VENT TUBE ASSEMBLY (for 1KD-FTV, SINGLE TANK TYPE)
E158805E06

NOTICE:
For 3 door vehicles, proceed to next step.

  1. Remove the fuel sender gauge.

    1. for 1KD-FTV, Single Tank Type: (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 (FS) - B-2
    Always
    Below 1 Ω
    A-3 (FE) - B-1

    Text in Illustration 
    *a
    Component without harness connected (Fuel Tank Vent Tube Assembly)
    *b
    Lower side (to Fuel Sender Gauge Assembly)
    *c
    Connector A
    *d
    Connector B



NG
REPLACE FUEL TANK VENT TUBE ASSEMBLY (Click here)
OK


10. INSPECT FUEL SENDER GAUGE ASSEMBLY (for 1KD-FTV, SINGLE TANK TYPE)
for 3 Door:
  1. Remove the fuel sender gauge.

    1. for 1KD-FTV, Single Tank Type: (Click here)

  1. A223162E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Float level is F
    12 to 18 Ω
    Float level is E
    405 to 415 Ω

    Text in Illustration 
    *a
    Component without harness connected (Fuel Sender Gauge Assembly)
    *b
    Float Level F (Upper)
    *c
    Float Level E (Lower)

for 5 Door:

  1. E201786E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F
    12 to 18 Ω
    Float level is E
    405 to 415 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector (Fuel Sender Gauge Assembly)
    *b
    Float Level F (Upper)
    *c
    Float Level E (Lower)



NG
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

11. INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (for 1KD-FTV, DOUBLE TANK TYPE)
E158805E06
  1. Remove the fuel sender gauge.

    1. for 1KD-FTV, Double Tank Type: (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 (FS) - B-2
    Always
    Below 1 Ω
    A-3 (FE) - B-1

    Text in Illustration 
    *a
    Component without harness connected (Fuel Suction With Pump and Gauge Tube Assembly)
    *b
    Lower side (to Fuel Sender Gauge Assembly)
    *c
    Connector A
    *d
    Connector B
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Single Tank Type)
    B
    NG (for Double Tank Type)
    C



NG
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)
OK


12. INSPECT FUEL SENDER GAUGE ASSEMBLY (for 1KD-FTV, DOUBLE TANK TYPE)

  1. E201786E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F
    12 to 18 Ω
    Float level is E
    405 to 415 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector (Fuel Sender Gauge Assembly)
    *b
    Float Level F (Upper)
    *c
    Float Level E (Lower)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Single Tank Type)
    B
    NG (for Double Tank Type)
    C



NG
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

13. INSPECT FUEL TANK VENT TUBE ASSEMBLY (for 5L-E)
E158805E06
  1. Remove the fuel sender gauge.

    1. for 5L-E, Single Tank Type: (Click here)
    2. for 5L-E, Double Tank Type: (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 (FS) - B-2
    Always
    Below 1 Ω
    A-3 (FE) - B-1

    Text in Illustration 
    *a
    Component without harness connected (Fuel Tank Vent Tube Assembly)
    *b
    Lower side (Fuel Sender Gauge Assembly)
    *c
    Connector A
    *d
    Connector B
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Single Tank Type)
    B
    NG (for Double Tank Type)
    C



B
REPLACE FUEL TANK VENT TUBE ASSEMBLY (Click here)

C
REPLACE FUEL TANK VENT TUBE ASSEMBLY (Click here)
A


14. INSPECT FUEL SENDER GAUGE ASSEMBLY (for 5L-E)

  1. E201786E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F
    12 to 18 Ω
    Float level is E
    405 to 415 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector (Fuel Sender Gauge Assembly)
    *b
    Float Level F (Upper)
    *c
    Float Level E (Lower)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Single Tank Type)
    B
    NG (for Double Tank Type)
    C



B
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

C
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)


← B1500 Fuel Sender Open Detected (Aug 2013 – Jul 2014)B1501 Sub Fuel Sender Open Detected (Aug 2013 – Jul 2014) →